ultraPLAY Discovery Center DC-1SM Assembly Instructions Manual Download Page 21

19

         

UltraPlay Play Systems

         800.458.5872  •  www.ultraplay.com

         

UltraPlay Play Systems

         800.458.5872  •  www.ultraplay.com

USE ZONE WITH POST PLACEMENT/HOLE LOCATIONS

21’   

22'

12’3”

32”

(813mm)

45-1/4”(1150mm)

7’ 1-1/2”

6’ 4-1/2”

32”(813mm)

69”(1753mm)

65”(1651mm)

67”(1702mm)

76”(1930mm)

12’

USE  Z

ONE

4

1

3

2

Vine

Climber

Straight

Slide

TOP VIEW

Placement for 

12” Diameter x 18” Deep Holes

for In-ground installation

         

IMPORTANT: Never install play equipment 

over hard, unresilient surfaces such as 

asphalt, concrete or compacted earth.  It is 

the owner’s responsibility to ensure the 

“minimum area required” contains an 

appropriate amount of resilient material to 

cushion accidental falls.

1. Review Use Zone. 

    Mark the placement of one Deck Post.      

    Any of the (4) may be used.

    NOTE:  Survey flags may be used to mark

                the placement of each hole.

2. Measure from first Deck Post to mark the positon

    of the remaining (3) posts.  Check for 

    squareness using the 45-1/4” diagonal dimension.

    NOTE:  All remaining dimensions are based off of

                 the Deck Post placement.

3. Measure from the center of a Deck Post using the       

    dimensions provided for each remaining hole.

Concrete Required(if applicable) :Approx. .3 Cubic Yards (.25 Cubic Meters)

NOTE: Suggested Min. concrete rating: 3000PSI

Deck

NOTE:

All dimensions are

measured from the

center of the posts/holes

INSTALLED  DIMENSIONS 

No Roof (DC-1SM)

With Roof (DC-1SMR)

12ft wide x 10ft long x 6ft 6in tall 

12ft wide x 10ft long x 10ft 6in tall 

Summary of Contents for Discovery Center DC-1SM



































































Reviews: