background image

Installation and Maintenance Manual

 

page 20 

of 23  -  

HYDRAULIC CYLINDER FOR SIDE MOUNT APPLICATIONS

5.2 Troubleshooting

Whenever  the  following  checks  need  the  removal  and/or  disassembly  of  the  steering  system  components,

such work must be carried by specialized staff. 

UFLEX 

offers general information only and is not responsible

for  any  consequences  resulting  from  incorrect  disassembly.

    PROBLEM

                CAUSE

                         SOLUTION

Blockage in the hoses between

steering  system  and  cylinder.

Air  in  the  system.

Leaks  from  the  cylinder

bleeder.

Coiled  hose.

Helm has been mounted upside

down.

Restrictions in hoses or fittings.

During  the  filling,  the

steering  system  becomes

completely  jammed.

The system is very difficult

to  fill.

Air  keeps  bubbling  at  the

top of the steering system

tank  even  after  filling  the

system  completely.

Replace  hoses.

Repeat  the    filling  and  the  bleeding

procedure  of  the  system.

Install  horizontally  the  hoses  and  in

any case with a  maximum inclination

of 3cm  each  meter.

Tighten  the  bleeder  on  the

cylinder.

Uncoil  and  straighten  the  hose.

Mount the helm with the filling hole in

up position.

Look  for  and  remove  the  restriction.

WARNING

WARNING

5.1 Ordinary maintenance

5 MAINTENANCE

Poor installation and maintenance may result in loss of steering and cause property damage and/or perso-

nal  injury.  Maintenance  requirements  change  according  to  climate,  frequency  and  the  use.    Inspections  are

necessary at least every year and must be carried out by specialized marine mechanics. Check the cylinder

fittings  and  the  seals  and  the  helm  gaskets  to  prevent  leaks.  Replace  them  if  necessary.

To  keep  a  suitable  oil  level  in  the  tank,  fill  and  bleed  the  system  as  described  in  this  manual  in  paragraph

3.6.

Check the hose and the entire system wear, the nut and bolt tightening every six months and make sure that

they  are  not  damaged.
Clean  the  system  using  water  and  non-abrasive  soap.

Use only compatible hydraulic oils,  indicated in the paragraph "technical features"  and  "filling and bleeding  ".

Do not use brake  oils or  automatic  transmission  fluid  (ATF)  in any  case.

WARNING

WARNING

The  damaged  hose  must  be  replaced,

otherwise  it  may  cause  loss  of  steering

and  severe  personal  injury  or  property

damage.

The steering system is stiff

and  hard  to  turn,  even

when  the  boat  is  not

moving.

Air  in  oil

Repeat  the    filling  and  the  bleeding

procedure  of  the  system.

Summary of Contents for UC 68-OBS

























Reviews: