background image

Page 3 of 8 

manual cannot cover all possible conditions or situations that could occur. It must be 

understood by the operator that common sense and caution are factors that cannot be built 

into this product, but must be supplied by the operator. 

 

SAVE THESE INSTRUCTIONS 

IMPORTANT SAFETY CONSIDERATIONS 

 

If mounting this product requires drilling holes, the installer MUST be sure that no 

vehicle components or other vital parts could be damaged by the drilling process. 

Check both sides of the mounting surface before drilling begins. Also de-burr any 

holes and remove any metal shards or remnants. Install grommets into all wire 

passage holes. 

 

WARNING

: The vehicle should never be driven at high speeds if the lighbar is 

magnetically mounted. If intended to be used at high speeds, user must permanently 

mount the lightbar. 

 

If this product is mounted with magnets, clean the mounting surface and dry it 

thoroughly before installation. 

 

Do not install this product or route any wires in the deployment area of your air bag. 

Equipment mounted or located in the air bag deployment area will damage or reduce 

the effectiveness of the air bag, or become a projectile that could cause serious 

personal injury or death. Refer to your vehicle owner

’s manual for the air bag 

deployment area. The User/Installer assumes full responsibility to determine proper 

mounting location, ensuring safety to all passengers inside the vehicle.   

 

Use only soap and water to clean the outer lens. Inspect and operate this product 

regularly to confirm its proper operation and mounting condition. 

 

LIGHTBAR

 

USE AND CARE 

 

It is strongly recommended to only plug 12V plug into 12V power port,

 as 

cigarette outlets can become contaminated and not create a good connection. 

 

Do not modify the lightbar in any way.

 Unauthorized modification may impair the 

function and/or safety and could affect the life of the product. 

 

Always check damaged or worn out parts before using the lightbar. 

Broken parts 

will affect the lightbar operation. Replace or repair damaged or worn parts 

immediately. 

Summary of Contents for 40511









Reviews: