background image

Pink

        Channel 4 Output

Programmable - See menu 2, setting 5.

Green

         (-) Door Input

Negative door pin switch input.

Blue

        (-) Hood Input

Negative input from hood pin switch.

Purple

         (+) Door Input

Positive door pin switch input.

Brown

         (+) Siren Output

Positive output for siren.

White

(+) Park lights

 Programmable - menu 2, setting 3.

Blk/White

         (+/-) Dome Light

Dome light supervision.

 See page 5.

Blk/White

         (+/-) Dome Light

Dome light supervision.

 See page 5. 

Orange

         (-) When Armed

Negative output when system is armed.

Grey

         (-) Trunk Release

     Positive

 trunk release.

 500ma max.

Yellow

     Ignition Input

  Input from vehicles ignition wire.

Black

        Ground Input

System ground input.

Red

        Main Power Input

Constant 12 Volt input.

Green

Door Lock

Programmable - menu 1, setting 3.

Red

       12 Volt Output

Output for voltage inverter.

Low Current Only

Blue

       Door Unlock

Programmable - menu 1, setting 3.

Pink

       Second Unlock

Programmable - menu 1, setting 3

4 Pin Connector Red

2 Pin Connector Blue

2 Pin Connector Red

3 Pin Connector White

4 Pin Connector White

Plug-in Program Button Connector.
The program Button is used to access the systems Programming Menu’s.
See page 5.  for installation instructions.

Plug-in LED Connector.
See page 5.  for installation instructions.

Green

  (-) When Disarmed

Negative output when disarmed.

Pink

   Horn / Channel 5.

       Programmable - See menu 2, setting 7

Blue

    (+) Disconnect

Triggers when 12volt circuit is broken.

Blue

       Sensor Full Warn

Input trigger for addition alarm sensor(s)

Green

       Sensor Pre Warn

Input trigger for addition alarm sensor(s)

Black

      Ground Output

   Ground output for addition alarm sensor(s)

Red

       12 Volt Output

     12 volt output for additional alarm sensor(s)

14 Pin Connector

PAGE 5

SECURITY SYSTEM

INSTALL GUIDE

Summary of Contents for 600 SERIES













Reviews: