background image

Recommended Pre-Installation Procedures

Feature List

- Control module

- 2 4 button transmitters*

- Antenna with built in

- 6 pin main harness with dual

- Program Button and LED’s

30 amp power inputs.

- Multi-tone Siren

- 3 pin auxiliary output harness

- 14 pin harness

- 4 pin Auxiliary sensor harness

- 4 pin keyless entry harness

- 2 pin Temperature Sensor (LT Models)

- Hood pin safety switch

- Starter disable harness

- Installation and Owner Manuals

* The 26xx comes with two 6 button remote transmitters

Remote car starters and alarms should be professionally installed.

Review the installation and owner manuals and acquire a vehicle wiring diagram for the
vehicle to be worked on. Take a few moments to walk around the vehicle looking for
any damages and make note if any are found. Also check other functions such as
vehicle lighting system, warning lights or check engine lights. Check if the vehicle has a
factory security or anti-theft. (Transponder or PASS-LOCK system) These systems will
require additional parts and labor to complete the installation. Use of the proper tools
and testing equipment is also very important. Never use a grounding style test light to
test for wires in the vehicle. Use only a Circuit Safe test light or digital Volt/Ohm Meter.
It is the sole responsibility of the installer to test and verify all connections

Note:

This remote starter system is designed for fuel injected and diesel engines.

If the vehicle is a manual transmission, a “M” series remote starter must be
installed. Any model number followed by the letter “M” is specially designed for
manual transmission vehicles. The “M” series remote starter will not work in an
automatic transmission vehicle.

Components

- Auto Tach learning with Quick Learn option

     - Turbo Timer Mode

- Starter Kill/ Anti-Grind Protection

           - Engine Idle Mode

- Remote Panic Feature

 - System Override Protection

- Programmable Wait to Start

     - Dual Car Operation

- Service Mode (Valet)

    - Park Light Diagnostics

- Active/Passive Arming

      - Program 4 Transmitter Codes

- Run Time 4/ 15 or 45 minutes

                - Ignition Auto Lock

- Door Locks .125s/ .75s/3.0s/Double Unlock         - Dual Stage Shock Sensor
- Cold Start With Four Start Intervals or Temp Mode (LT Models Only)

REMOTE VEHICLE STARTER/ALARM

INSTALLATION MANUAL

Page 3

Summary of Contents for 25XX Series

























Reviews: