background image

    ALARM MODELS ONLY                 

3 CHIRPS

Press & HOLD Lock + Unlock buttons at the same time

Press & HOLD Lock + Unlock buttons at the same time

Each time the lock button is pressed and released the sensitivity will 
INCREASE by 1 level. This is confirmed by a series of park light flashes 
& SIREN Chirps 

Each time the unlock button is pressed and released the sensitivity will 
DECREASE by 1 level. This is confirmed by a series of park light flashes 
& SIREN Chirps 

Continue to hold the buttons for 3-5 seconds until the SIREN 
Chirps 3 times

1 - ENTER SHOCK SENSOR ADJUSTMENT MODE

2 - ADJUSTING THE SHOCK SENSOR

3 - EXITING SENSOR ADJUSTMENT MODE

+

+

(Note: System will Arm or Disarm via silent arming prior to entering adjustment mode)

(1 Flash / Chirp is the least sensitive setting & 10 Flashes  / Chirps is the most 
sensitive)

(1 Flash / Chirp is the least sensitive setting & 10 Flashes  / Chirps is the most 
sensitive)

(NOTE: Shock Sensor Adjustment Mode has an auto time out of 8 seconds)

If the system has been triggered (shock sensor, door input..), the siren will sound for 
approximately 60 seconds. Press and release the lock or unlock button to silence the siren 
(the system will remain armed). Press the unlock button to disarm the system. The siren 
and park lights will flash three times to indicate the system had been triggered.

SYSTEM PROGRAMMING - 

Menu 1

PAGE 27

80 SERIES

INSTALL MANUAL

 QUICK VIEW OPERATIONS

SYSTEM PROGRAMMING - 

Menu 1

PAGE 26

80 SERIES

INSTALL  MANUAL

 SHOCK SENSOR SETTINGS 

SYSTEM PROGRAMMING - 

Menu 1

QUICK VIEW OPERATION CHART

 1 SECOND

 3 SECONDS

1 SECOND (PANIC OR ALARM) 

 1
 1

 OFF

LOCK / ARM ALARM

  ACTIVATE PANIC

ALARM/ PANIC OFF

 1 SECOND

1 SECOND (PANIC OR ALARM)

HOLD FOR 3 SECONDS

2

OFF

2 + 1

UNLOCK  / DISARM

ALARM/ PANIC OFF

TRUNK

1 SECOND

1 SECOND WHEN RUNNING

3 SECONDS W/ REMOTE START

1
1
2

 REMOTE START

EXTENDED RUNTIME

SHUTDOWN

HOLD FOR 3 SECONDS

PRESS AND RELEASE

5 LONG

STATUS

CAR FINDER MODE

STATUS CHECK ON 2WAY

BUTTON

LENGTH OF PRESS

 CHIRPS / 

FLASHES

SYSTEM OPERATION

** PLEASE SEE OWNERS GUIDE FOR DETAILED OPERATIONS AND FEATURES

SERVICE MODE / EMERGENCY OVERRIDE

TO AVOID SERIOUS INJURY, this remote start system must be set into Service Mode 
before any under hood servicing is started. Service Mode will prevent the vehicle from 
starting while the vehicle is being serviced. It is the sole responsibility of the vehicle’s 
owner to place the system into Service Mode. The manufacture accepts no 
responsibility for accidental starting of the vehicle while the vehicle is being serviced.

ACTIVATING  / DEACTIVATING VALET MODE / EMERGENCY OVERRIDE

Turn the Ignition Key ON

(Leaving the key ON)

Press and hold the Valet switch for 8 to 15 seconds 
(Time depends on "Valet Settings" Program Option) 

 REMOTE START AND ALARM DEACTIVATED

 REMOTE START AND ALARM ACTIVATED

 5 CHIRPS = OFF

 2 CHIRPS = ON

Summary of Contents for 1280 series

































Reviews: