4 PIN AUXILIARY SENSOR CONNECTOR*
FULL TRIGGER INPUT
BLACK
GROUND OUTPUT FOR AUXILIARY SENSOR
GREEN
BLUE
PRE-WARN TRIGGER
RED
12VOLT OUTPUT FOR AUXILIARY SENSOR
1- BLUE Pre-Warn Trigger (-) Input
When this wire is grounded by an auxiliary sensor (i.e: Radar Sensor) the system will chirp the SIREN 3 times.
2- GREEN Full Alarm Trigger (-) Input
When this wire is grounded by an auxiliary sensor (i.e: Radar Sensor) the alarm will activate for up to 60 sec.
3- BLACK Sensor Ground Output (-)
This wire provides a ground output for the auxiliary sensor.
4- RED Sensor 12volt Output (+)
This wire provides a 12volt output for the auxiliary sensor.
*ALARM MODELS ONLY
1- WHITE/VIOLET Wire-Ground When Running (-)
Connect this wire to the your bypass modules negative turn on wire. When the remote starter is activated
this wire will switch to ground.
2- BLACK Wire- System Ground (-)
Connect this wire to the ground input on the bypass module.
3- RED Wire- 12volt Power Input (+)
Connect this wire the 12volt input on the bypass module.
3 PIN BYPASS CONNECTOR
SYSTEM CHASSIS GROUND INPUT
RED
CONSTANT 12 VOLT INPUT (20AMP)
BLACK
WHITE/VIOLET
GROUND WHEN RUNNING OUTPUT
***DATA LINK CONNECTOR - FOR USE WITH COMPATIBLE BYPASS MODULES ONLY***
4 PIN DATA BYPASS
Input trigger to start
The remote starter will activate when this wire is pulsed with ground.
*Available with plug-in thermistor for temperature start on LT models.
2 PIN THERMISTOR/ START TRIGGER
SYSTEM PROGRAMMING -
Menu 1
SYSTEM PROGRAMMING -
Menu 1
PAGE 14
PAGE 15
80 SERIES
80 SERIES
INSTALL MANUAL
INSTALL MANUAL
SYSTEM WIRING DETAILS
PROGRAM MODE
Press Lock
Press Unlock
Press Start
Press #
MENU 1
MENU 2
MENU 3
MENU 4
1 - Cycle the Ignition Key On/Off On/Off On (Leaving the key ON)
2 - Press and release the Program Switch 1 time. (The park lights will turn on and the HORN will chip to
confirm that program mode was entered)
3 - Select the Program Menu by pressing...
ENTERING PROGRAM MODE
1 -
Cycle the Ignition Key On/Off On/Off On (
Leaving the key ON
)
2 -
Press and
RELEASE
the Program Switch 1 time.
(HORN/ SIREN will chip to confirm that program mode was entered)
3 -
Press and
HOLD
the Program Switch for until the HORN/SIREN Chirps 3 times.
4 - Turn ignition key
OFF
to exit.
SYSTEM RESET
TRANSMITTER PROGRAMMING
1 -
Cycle the Ignition Key On/Off On/Off On.
(Leaving the key ON)
2)
Press and
HOLD
the Program Switch.
(The HORN/ SIREN will chirp 1 time,
CONTINUE to HOLD)
**If the HORN/ SIREN does not chirp turn the key off, then repeat step 1**
3)
Continue to
HOLD
the Program Switch and the HORN/ SIREN will chirp 5 times.
4)
Press the
LOCK BUTTON
on each of remote’s to be programmed.
*Pause for about 1 second between programming of each remote.
System can accept 4 remote’s max.
5)
The park lights will flash once and the HORN/SIREN will chirp once each time a new code is learned.
6)
Release the Program switch and turn Ignition OFF.
4 - Press and Release the Program Switch to advance through the settings.
(
Confirmed by HORN/ SIREN chirps & LED flashes)
5 - Press and hold the Program Switch to change the setting
.
(Confirmed by HORN/ SIREN Chirps)
6 -
To exit Program Mode, turn key off.
(Confirmed by Long HORN/ SIREN Chirp)
SELECT AND CHANGE
