D
a
te
In
it
ia
ls
IN
S
P
E
C
T
IO
N
L
O
G
S
E
R
IA
L
N
U
M
B
E
R
:
S
E
E
R
F
ID
T
A
G
Manufacturer's instructions must be read and understood prior to use. Instructions
supplied with this product at time of shipment must be followed. Failure to do so
could result in serious injury or death. Contact Ultra-Safe if instruction sheet is
needed. Inspect before each use. Do not use if wear or damage is present. This
body harness is intended to be used to arrest the most severe free falls. Items
subjected to fall arrest or impact forces must be immediately removed from service
and destroyed. Connecting snap and d-ring must be compatible in size, shape, and
strength. This item is not flame or heat resistant. Repairs only to be performed by
Ultra-Safe. Equipment modification or misuse voids warranty.
WARNING
1. BACK 'D' RING IS FOR FALL ARREST
2. SHOULDER 'D' RINGS. (IF PRESENT) ARE FOR RETRIEVAL USE
ONLY USE LOCKING SNAPS.
3. SIDE 'D' RINGS (!F PRESENT) ARE FOR POSITIONING ONLY.
4. FRONT 'D' RING (IF PRESENT) ARE FOR FALLS GREATER THAN
24" WITH A MAXIMUM IMPACT OF 900 LBS. INSPECTION CARD
5. HIP ATTACHMENT ELEMENTS ARE FOR WORK POSITIONING
OR TRAVEL RESTRAINT
6. PARK LANYARD HERE
7. LOAD INDICATOR
EXAMPLE
OF TAGS
1.
2.
3.
4.
5.
6.
7.
Users of personal fall arrest systems shall, at a minimum, comply with all
manufacturer instructions regarding the inspection, maintenance and storage of
the equipment. the user's organization shall retain the manufacturer's instructions
and make them readily available to all users. See ANSI/ASSE Z359.2, Minimum
Requirements for a Comprehensive Managed Fall Protection Program, regarding
user inspection, maintenance and storage of equipment.
1. In addition to the inspection requirements set forth in the manufacturer's
instructions, the equipment shall be inspected by the user before each use and,
additionally, by a competent person, other than the user, at interval of no more
than one year for:
• Absence or illegibility of markings.
• Absence of any elements affecting the equipment form, fit or function.
• Evidence of defects in, or damage to, hardware elements including cracks,
sharp edges, deformation, corrosion, chemical attack, excessive heating,
alteration and excessive wear.
• Evidence of defects in or damage to strap or ropes including fraying,
unsplicing, unlaying, kinking, knotting, roping, broken or pulled stitches,
excessive elongation, chemical attack, excessive soiling, abrasion,
alteration, needed or excessive lubrication, excessive aging
and excessive wear.
2. Inspection criteria for the equipment shall be set by the user's organization.
Such criteria for the equipment shall equal or exceed the criteria established by
this standard or the manufacturer's instructions, whichever is greater.
3. When inspection reveals defects in, damage to, or inadequate maintenance of
equipment, the equipment shall be permanently removed from service or undergo
adequate corrective maintenance, by the original equipment manufacturer or their
designate, before return to service.
4. Maintenance and storage of equipment shall be conducted by the user's
organization in accordance with the manufacturer's instructions. Unique issues,
which may arise due to conditions of use, shall be addressed with the
manufacturer.
5. Equipment which is in need of, or scheduled for, maintenance shall be tagged as
unusable and removed from service.
6. Equipment shall be stored in a manner as to preclude damage from
environmental factors such as temperature, light, UV, excessive moisture, oil,
chemicals and their vapors or other degrading elements.
User Inspection, Maintenance, and Storage of Equipment
NOTE: LOAD INDICATOR IS PROTECTED BY ELASTIC BAND
H
O
5
6
2
1
4
5000lbs. M.B.L. Soft Loop Made for Non-Conductive Applications and/or Impalement Reasons
ALSO AVAILABLE IN
