ULTIMATE SPEED ULG 3.8 A1 BATTERY CHARGER, Operation And Safety Notes

Page: 10 / 72

10 GB
Operation
Q
reset / deleting settings
After connection to the power supply, the appliance
automatically returns to its basic setting and remains
in STANDBY mode
Q
Switching between modes 1,
2, 3 and 4
j
Press the MODe selection button
9
the appro-
priate number of times.
The device switches between charging modes in
the following order: Standby , MODe 1
„6 V“, MODe 2 , MODe 3
, MODe 4
and then repeats the cycle
nOTe:
If a 12 V battery is connected, MODe 1 “6 V”
cannot be selected. If a 6 V battery is connected,
MODeS 2, 3 and 4 “12 V” cannot be selected.
nOTe: If you press the selector button
9
, charging
mode automatically switches over to the next mode
and begins operation in that mode.
nOTe: However, if a battery is not disconnected
from the charging station after a full charge, the
appliance remains in trickle-charge mode, even if
the user switches over to another mode. This pro-
tects the battery from being damaged.
Q
Mode 1 „6 V“ (7.3 V / 0.8 A)
This mode is suitable for charging 6 V lead-acid
batteries with a capacity less than 14 Ah.
j
Press the selection button MODe
9
, to select
mode 1. After doing so, the corresponding leD
display „6 V“
2
lights up. If you do not activate
an-other process afterwards, the electronic sys-
tem will automatically start the charging process
together with the leD display
8
at (with a
current of) 0.8 A ± 10 %. If the procedure runs
without any problems, the leD display
8
remains on during the entire charging process, un-
til the battery is fully charged at 7.3 V / ± 0.25 V.
When the battery is fully charged, leD display
7
lights up and leD display
8
goes
out. The device now switches automatically into
maintenance charging mode.
Q
Mode 2 „12 V“ (14.4 V / 0.8 A)
This mode is suitable for charging 12 V lead-acid
batteries with a capacity less than 14 Ah.
j
Press the selection button MODe
9
, to activate
mode 2. After completion of this process, the
appropriate leD indicator
3
lights up.
Then if you do not take any further action, the
electronic control and the leD indicator
8
automatically switches on and starts the charg-
ing process. If the procedure runs without any
problems, the leD display
8
remains on
during the entire charging process, until the
battery is fully charged. When the battery is
fully charged, leD display
7
lights up and
leD display
8
goes out. The device now
switches automatically into maintenance charg-
ing mode.
Q
Mode 3 „12 V“ (14.4 V / 3.8 A)
This mode is mainly suitable for charging 12 V
lead-acid batteries with a capacity greater than
14 Ah under normal conditions.
j
Press the selection button MODe
9
, to activate
mode 3. Then if you do not take any further ac-
tion, the electronic control and the leD indicator
4
switches on and starts the charging pro-
cess. If the process runs without any problems,
the leD indicator
8
remains on during the
whole charging process until the battery is
charged. When the battery is fully charged, the
leD indicator
7
and the die leD indicator
8
go out. The device now switches auto-
matically into maintenance charging mode.
66292_uls_Batterieladegeraet_content_PL-HU-SI-CZ-SK.indd 10 13.05.11 12:33