background image

Installation Manual 

UL

POWER

 

UL390i UL390i

S

 390i

SA 

 

 

MI 390A01 Revision No: 3 

Date:  

2014-09-15

 

Page: 

57 

of

 69

 

The  provided  copper  clamps  are  used  on  one  end  of  each  lead  and 
screw  into  the  ignition  coil  cover.  Strip  only  a  few  millimetres  of  the 
outer plastic of the ignition lead to unveil the inner core. It is advisable 
to solder the copper clamp onto the lead for good contact. The ignition 
lead is held and guided behind the point of soldering so no bending and 
as a result cracking should occur on the soldering. 

Push in the lead with the clamp all the way into the ignition coil cover 
and then screw on the cover with a couple of turns. Make sure the lead 
is fixed tightly and it cannot be pulled out by a small force. 

The  ignition  coil  cover  clicks  onto  the  ignition  coil.  Make  sure  you  get 
the correct leads going to the correct spark plugs. 

The other side of the lead is screwed in the spark plug cover. Cut the lead to the requested length. 
Do not strip the plastic, but screw the spark plug cover into it. Do not forget to first slide the rubber  
sealing  over  the  lead  before  attaching  it  to  the  spark  plug  cover.  When  attached  pull  back  the 
rubber to cover the joint and make it moisture proof. 

Slide  the  bottom  rubber  over  the  spark  plug  cap  and  click  the  cap  onto  the  corresponding  spark 
plug. 

 

Each cylinder head has 2 spark plugs; each going to a different coil for redundancy. 

Cylinder numbering is done from the propeller backwards. See numbering below.  

 

Summary of Contents for UL390i






































































Reviews: