background image

4. Using NOTCH Feature:

a. Press MENU until NOTCH is displayed on LCD.
b. Press “+” twice. The 5 cent icon will flash for 3 seconds and then disappear. That    
    means 5 cent is “notch out” (eliminated). The detector will have no response to     
    5cent. To eliminate “ZN”, press “+” four times. The “Zn” icon will flash and then  
    disappear.
c. Wave a 5 cent coin or Zinc Penny over the search coil. They will not be detected 
    because they have been “notched out”(eliminated). Notice the target categories 
    not displayed on LCD can not be detected.
    For fast proceeding, press MENU while the icon is flashing to accept the Notch.
    To pick up the target eliminated, press “+” or “-” to have the target icon flash and    
    then press MENU.

5. Using PINPOINT Feature:

a. Press and hold PP. “PP” momentarily appears on the LCD.
b. Hold a coin motionless over the search coil.
c. Lower coin toward search coil and then raise coin away from search coil.
d. Notice that the sound changes as the coin moves closer and farther.
e. Notice that the depth indicator changes as the coin moves up and down.

6. Adjusting SENS(SENSITIVITY)

a.Press MENU until SENS is displayed on LCD.
b.Press “+” or “-” to set the desired level. Sensitivity level can be set from 1-10. The   
   relative digital value will be displayed on LCD when “+” or “-” is pressed.

7. Adjusting VOLUME

a.Press MENU until VOLUME is displayed on LCD.
b.Press “+” or “-” to set the desired level. VOLUME level can be set from 0-10. The  
   relative digital value will be displayed on LCD when “+” or “-” is pressed.

OVERLOAD WARNING

If a metal object or highly magnetic soil are too close to the search coil, the
detector will overload and “- - ” will appear on LCD. The detector will make a rapid, 
repeating mid-tone warning sound. Overload will not harm the detector, but the 
detector will not function under these conditions. If overload occurs, raise the 
search coil to detect the target from a greater distance, or move to a different 
location.

9

Summary of Contents for GC-1071
















Reviews: