background image

7

installinG the new water heater

mountinG

mountinG - drYwall (hollow wall)

1.  The selected wall or cabinet must be capable of supporting double 

the weight of the unit when completely full of water (77 Ibs).

2.  The  installation  area  must  provide  adequate  clearances  for 

removal of the front panel and servicing the unit.

3.  Locate  the  wall  studs  in  the  area  where  the  unit  is  to  be 

mounted.

4.  Cut two sections of 1/2 inch plywood or equivalent material 3 

inches in height. The length of each section should be sufficient 

to span the width of the wall studs. See Figure 3A.

5.  Use appropriately sized nails or wood screws to attach the two 

wall supports to the wall as show in Figure 3A.

6.  Drill two 13/32 inch holes in the upper wall support NOTE: The 

holes must be level.

7.  Insert the hollow wall anchors into the drilled holes. Place the 

wall bracket over the anchors and screw the two phillips head 

screws down tight against the bracket.

mountinG - masonrY wall (solid wall)

1.  The selected wall or cabinet must be capable of supporting double 

the weight of the unit when completely full of water (77 Ibs).

2.  The installation area must provide adequate clearances for 

removal of the front panel and servicing the unit.

3.  Drill  two  13/32  inch  holes  in  the  masonry  wall.  NOTE: The 

holes must be level and at least 3-1/2 inches deep.

4.  Insert the masonry wall anchors into the drilled holes. Place 

the wall bracket over the anchors and screw the two phillips 

head screws tight against the bracket.

fiGure  3a.

mountinG - floor

1.  The floor selected must be capable of supporting double the 

weight of the unit when completely full of water (77 Ibs).

2.  The  installation  area  must  provide  adequate  clearances  for 

removal of the front panel and servicing the unit.

3.  Place a suitable drain pan under the unit. The pan must limit the 

water to a maximum depth of 2-1/2 inches and be 2 inches wider 

than the unit. The pan must also be piped to an adequate drain. 

See Figure 3B.

fiGure  3B.

water pipinG

HOTTER  WATER  CAN  SCALD: 

Water heaters are intended to produce hot water. Water heated to 

a temperature which will satisfy space heating, clothes washing, 

dish  washing,  cleaning  and  other  sanitizing  needs  can  scald  and 

permanently injure you upon contact. Some people are more likely to 

be permanently injured by hot water than others. These include the 

elderly, children, the infirm, or physically/mentally disabled. If anyone 

using hot water in your home fits into one of these groups or if there 

is a local code or state law requiring a certain temperature water at 

the hot water tap, then you must take special precautions. In addition 

to using the lowest possible temperature setting that satisfies your 

hot water needs, a means such as a mixing valve should be used at 

the hot water taps used by these people or at the water heater. 

Valves for reducing point of use temperature by mixing cold and 

hot water are also available.

Consult a Qualified Installer or Service Agency. Follow manufacturer’s 

instructions for installation of the valves. Before changing the factory 

setting on the thermostat, read the “Temperature Regulation” section 

in this manual.

Summary of Contents for 2.5 Gallon 120 volt water heater





















Reviews: