background image

3

PROCEDURES).

4 TO OPERATE SAFELY
1

Do not

 operate the dispenser without

reading this operator’s manual.

2

Do not

 operate the dispenser unless it is

properly grounded.

3

Do not

 use extension cords to connect the

dispenser.

4

Do not 

operate the dispenser unless all

panels are restrained with screws.

5

Do not

 obstruct air intake and discharge

openings: 15 cm (6”) minimum air space all
around the dispenser.

6

Do not

 put objects or fingers in panels

louvers and faucet outlet.

7

Do not

 remove bowls, augers and mixers for

cleaning or routine maintenance unless the

dispenser is disconnected from its power source.

5 OPERATING PROCEDURES
1

Clean and sanitize the unit according to the

instructions in this manual. See chapter 5.3
CLEANING AND SANITIZING PROCEDURES.

2

Fill the bowls with product to the maximum

level mark. Do not overfill.
The exact quantity of product (expressed as
liters and gallons) is shown by marks on the
bowl.

3

In case of products to be diluted with water,

pour water into bowl first, then add correct
quantity of product. In case of natural squashes,
it is advisable to strain them, in order to prevent
pulps from obstructing the faucet outlet.

4

Install the covers and check that they are

correctly placed over the bowls.

5

Set the control switches as shown in chapter

5.1 DESCRIPTION OF CONTROLS.

6

The dispenser must always run with the

c o v e r s   i n s t a l l e d   t o   p r e v e n t   a   p o s s i b l e
contamination of the product.

7

Always leave the dispenser on, as the

refrigeration stops automatically when the
beverage reaches the dispensing temperature.
The mixing devices will continue to turn.

8

To maintain a high standard of flavour, keep

refrigeration and mixing devices on during the

night when beverage is in the bowl.

5. 1 DESCRIPTION OF CONTROLS

The dispenser is equipped with the power
switch only. When it is set to position I, the
power is turned on both to mixing devices and
to refregeration.

Beverage temperature adjustment (models 7/
1 and 10/1 only): turn the knob, located on the
right of the faucet side of the dispenser,
toward right to decrease temperature or
vicevarsa.

5. 2 HELPFUL HINTS
1

The length of time for cooling down the

product is governed by many variables, such as

IMPORTANT

Install  the dispenser so that the plug is
easily accessible.

ATTENTION

In case of damages, the power cord must
be replaced by qualified personnel only in
order to prevent any shock hazard. 

IMPORTANT

Operate the dispenser with food products
only.

IMPORTANT

Should despenser be operated without
using all the bowls (left bowl, facing the
unit from dispensing side, must be always
used) it is advisable to remove (see 5.3.1
DISASSEMBLY paragraph) the pump
impeller from the empty bowls.
If operated without liquid, the impeller
would be seriously damaged.

Summary of Contents for CADDY UL













Reviews: