UEi DL220 Instruction Manual Download Page 6

Page: 6 / 6

Battery Replacement

•

When the batteries are too low for safe operation, the Low Battery

indicator will display.

• Rotate latches until Unlock symbols are aligned with arrows. Remove

battery cover.

•  Replace the old batteries with 2 new (AAA) batteries.
•  Replace the battery cover
•  Rotate latches until the lock symbols are aligned with arrows.

S/N:

CA
TIV

600V

CA
TIV

600V

OPEN

LOCK

OPEN

LOCK

OPEN

LOCK

OPEN

LOCK

Test Lead Notes

CatIV 600V Measurement Locations

• Ensure the test lead shield is pressed firmly in place. Failure to use the

CATIV shield increases arc-flash risk.

CATII 1000V Measurement Locations

• CATIV shields may be removed for CATII locations. This will allow testing on

recessed conductors such as standard wall outlets. Take care not to lose

the shields

4mm

CATIV

600V

CATIV

600V

CATII

1000V

18mm

4mm

CATIV

600V

CATIV

600V

CATII

1000V

18mm

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for DL220







Search results

Summary of Contents for DL220

Reviews:

Related manuals for DL220

Brands by name

Popular brands

UEi DL220, Instruction Manual

Search results

Summary of Contents for DL220

Reviews:

Related manuals for DL220

Brands by name

Popular brands