manualshive.com logo in svg

UEC DSD 700, Operating Instructions Manual

Share
Download
UEC DSD 700 Operating Instructions Manual Download Page 8

 8

       OPERATING INSTRUCTIONS

   DSD 700

Optional Decoder Connections

Introduction

There are several ways of connecting the DSD to an existing
entertainment system.

The following more common examples enable you to view satellite
services and terrestrial channels, record and playback from a VCR
and listen to CD quality stereo sound on a Hi-Fi.

Consult your local installer for assistance in setting up an audio/
video configuration best suited to your requirements.

Hints to Quality TV System Configurations

•

Where possible, connect cables via audio/video outputs/inputs
(SCART or RCA) instead of RF connectors.

•

Use an appropriate, correctly installed satellite dish system.

•

Ensure that the system is properly earthed and protected
against lightning.

•

Use high quality stereo TV and Hi-Fi equipment.

•

Use high quality screened cables.

NOTE:

When Video and Audio Inputs/Outputs are used, it
may be necessary to select the Video/ Audio mode
on the VCR and TV  in place of theTV mode.

DSD, TV (most common connection)

1

Connect the terrestrial antenna connector to the RF IN socket
on the IRD.

NOTE:

It is recommended that you switch off the mains

                supply to the DSD before connecting or

disconnecting the LNB connector to/from  the
decoder

2

Using a SCART-to-SCART cable, connect the TV SCART
socket on the IRD to the SCART socket on the TV.

OR

3

If the TV does not have a SCART connector, use the supplied
flylead to connect the RF OUT socket of the IRD to the
RF IN socket on the TV.

OR

4

If using RCA connectors, connect betweenDSD audio and
video connectors and respective RCA connectors on the TV.

OR

5

If using SCART to RCA connector, connect between the DSD
TV SCART output and RCA connectors on the TV.

OR

6

If your TV has a S Video connector, connect to S VHS
connector on the decoder. Also, connect Mono Audio on
decoder to Audio In on the TV.

7

Connect the coaxial cable connector from the LNB on the
satellite dish into the socket marked LNB IN on the DSD.
The connector on the coaxial cable should be turned until it
is finger tight

RF OUT

RF IN

MONO
AUDIO

VIDEO

OUT

STEREO AUDIO

OUTPUTS

R

L

DATA SERVICE

WARNING! High Voltage
DANGER! Do not open
Unauthorised opening
renders warranty invalid
Protect against moisture

LNB IN

LNB OUT

F

I

X
E
D

V
A
R

I

A
B
L
E

VCR

EXTERNAL MODEM

Republic of South Africa

400 mA max.

210 - 250V     50Hz  30W

REAR PANEL

TV

RF IN

AV CONNECTIONS

SC ART TO  RCA

SCART TO SCART

AUDIO IN

VIDEO IN

NOTE:  CONNECT EITHER RF IN TO RF OUT

OR RCA TO RCA 

S-VHS

S VIDEO

TV/AUX

Summary of Contents for DSD 700

































Reviews:

No comments

Brands by name

Popular brands

Load more brands