DSD 700
OPERATING INSTRUCTIONS
25
5
Press and to set the output signal of the selected SCART
Output.
6
Store the setting by pressing OK on the RCU.
7
Press EXIT to return to the previous menu or MENU to return to
the service.
Change Modem Settings (if fitted)
The Change Modem Settings screen allows the user to select Pulse or
Dial Tone for the modem, and (if applicable) to define a prefix string for
the modem.
1
Press MENU on the RCU.
The Menu Options list is displayed.
2
Press to highlight Advanced Options.
3
Press OK.
The Advanced Options Menu is displayed.
4
Press to highlight Change Modem Settings.
5
Press OK.
The Change Modem Settings screen is displayed.
6
Press or to highlight the field to be edited.
7
Edit the Pulse/Tone setting using and
.
8
Edit the Prefix digits using the numbered buttons and as
backspace.
9
Press OK to activate the setting and leave the screen.
10
Press EXIT to return to the previous menu or MENU to return to
the service.
Local Time
Greenwich Mean Time is transmitted via the satellite signal and re-
ceived by the IRD. If the user lives in a different time-zone, the IRD must
be set up during installation to show the correct local time for the Local
Time. In order to set the time do the following :
1
Press MENU on the RCU.
The Menu Options list is displayed.
2
Press to highlight Advanced Options.
3
Press OK.
The Advanced Options Menu is displayed.
4
Press to highlight Local Time.
5
Press OK.
The Local Time screen is displayed.
6
Press and to add or subtract offsets of 30 minutes until
the local time displayed shows the actual time for your location.
7
Press OK to save the setting and leave the screen.
8
Press EXIT to return to the previous menu or MENU to return to
the service.
IRD Upgrade
Upgrades involve replacing the software (programs) in the DSD with
improved software, adding more features and improving the existing
operation of the DSD. This ensures that the DSD does not have to be
replaced each time advances in technology occur.
DSD software upgrades normally take place automatically over-the-
air. The DSD can be upgraded when it is in standby or while it is
switched to a channel. The DSD cannot be upgraded if it is switched
off at the mains. It is strongly recommended that your DSD is in standby
when you are not using it (you do this by pressing on the RCU).
The Mail Menu will usually warn you that a software upgrade will take
place.
A facility is provided whereby you can check if new software is
available and you can then start the upgrade yourself. This is
necessary if the DSD has not been upgraded over-the-air due to, for
instance, prolonged power failures.
To upgrade the DSD software or check whether an upgrade is avail-
able, carry out the following:
1
Press the menu button on the RCU once. (the Main Menu will
appear on the TV set.)
2
Highlight ORGANISING SERVICES using the up/down arrows of
the RCU.
3
Press the OK button on the RCU.
4
Highlight the FULL RESCAN option.
5
Press the OK button on the RCU.
6
Press the OK button again to confirm the RESCAN.
7
Wait for the decoder to complete the rescan.
8
Press MENU on the RCU. The Main Menu is displayed.
9
Press to highlight Advanced Options.
10
Press OK.
The Advanced Options Menu is displayed.
11
Press to highlight IRD Upgrade.
12
Press OK.
The Upgrade screen is displayed with the message “Checking for
upgrade”. At this point, depending on whether an upgrade is available
or not, one of the following two messages appears on your TV screen:
Failure: no download found
. or
The upgrade will take
approximately X minutes
. Press OK to continue or EXIT to cancel.
If no upgrade is available, the decoder will return to the service.
If an upgrade is available but you do not wish to upgrade, press EXIT
to return to the previous menu.
13
If you wish to upgrade press OK. A message is displayed:
The upgrade is active and will take approximately X
minutes
After the download is completed, the decoder will return to the
current service.
