manualshive.com logo in svg

UEC DSD 700, Operating Instructions Manual

Share
Download
UEC DSD 700 Operating Instructions Manual Download Page 1

DSD 700

      OPERATING INSTRUCTIONS

            1

Contents

Unpacking ...................................................................................

2

Safety ...........................................................................................

2

Preface .........................................................................................

2

Digital Satellite Services ............................................................

2

Conditional Access ....................................................................

3

Smart Card ................................................................................... 3
     Inserting the Smart Card ......................................................... 3

The Digital Satellite Decoder (DSD) .......................................

4

Display .......................................................................................... 4
Front Panel Keys .......................................................................... 4
Rear Panel Connections .............................................................. 4

Remote Control Unit ...................................................................

5

Replacing Batteries in the RCU ................................................... 5

Getting Started ............................................................................

6

Installation of the satellite dish and cabling to the decoder ......... 6
      Installation Indemnity ............................................................. 6
Setting-up the System .................................................................. 6
Switching on the Decoder at the Mains ....................................... 6
Tuning your TV ............................................................................. 6
Adding a Modem .......................................................................... 7
Standby and Normal Modes ......................................................... 7
Optional Decoder Connections .................................................... 8
     Introduction .............................................................................. 8
     Hints to Quality TV System Configurations ............................ 8
     IRD, TV ..................................................................................... 8
     IRD, VCR, TV (using SCART or RF Interfaces) ...................... 9
     IRD, TV (SCART or RF Interfaces), Hi-Fi ................................ 10
     IRD,  VCR, TV, Hi-Fi ................................................................. 11
     IRD, VCR, TV, Hi-Fi (using RCA connectors) ......................... 12

Bouquet Selection ......................................................................

13

     Selecting Specific Services .................................................... 13
     Selecting Services Directly ..................................................... 13
     Stepping through Services ...................................................... 13
     Stepping using the RCU .......................................................... 13
     Stepping using the Decoder Front Panel Keys ...................... 13
     Selecting Specific Services from the EPG ............................. 14
     Selecting Services from the Information Bar .......................... 14

Controlling the Functions .......................................................

14

     Volume Control using the RCU Keys ...................................... 14
     Volume Control using the Decoder Keys ................................ 14
     Mute ......................................................................................... 14
     Displaying Subtitles or Teletext ............................................... 14
          Subtitles ............................................................................. 14
          Teletext ............................................................................... 14
    Clock ......................................................................................... 15
    Selecting Soundtracks ............................................................. 15
    Power Reset ............................................................................ 15
    Signal Source Selection ........................................................... 15

Open TV Electronic Programme Guide ...............................

15

Using the EPG ............................................................................... 15
   Now/Next EPG ........................................................................... 15
   Extended EPG ............................................................................ 16
   Theme Search ........................................................................... 17

Open TV Information Bar ........................................................

17

Reminders .................................................................................

17

Parental Blocking ......................................................................

17

Menu Navigation Route .............................................................

18

Using Menus ...............................................................................

19

Language Selection ...................................................................... 19
    Language Option in Guide & Menu .......................................... 19
    Soundtrack Options .................................................................. 19

Parental Control ............................................................................ 20
     Setting the Parental Level ....................................................... 20
     Changing the Parental Pin Code ............................................ 20

Information Box Display Period .................................................... 21

Organising Service ....................................................................... 21
     Sort TV Services ..................................................................... 21
     Reset TV Services .................................................................. 21
     Sort Audio Services ................................................................. 21
     Reset Audio Services .............................................................. 21
     Full Rescan .............................................................................. 22

Mail Messages .............................................................................. 22

Advanced Options ........................................................................ 22

     Change Dish Installation ......................................................... 22
          LNB Configuration .............................................................. 22
          Signal Setup ....................................................................... 23
          Tune IRD ............................................................................. 23
          Reset to Factory Defaults .................................................. 23
          Loop Through ..................................................................... 23
     Signal Detection ....................................................................... 23
     Information ............................................................................... 23
          IRD Status ........................................................................... 23
          CA Status ........................................................................... 23
          Loader Status ..................................................................... 23
     TV Installation .......................................................................... 24
          TV Type .............................................................................. 24
          Aspect Ratio ....................................................................... 24
          UHF Tuning ......................................................................... 24
          Scart Source ...................................................................... 24
          Scart Video Output ............................................................ 24
     Change Modem Settings (if fitted) .......................................... 25
     Local Time ................................................................................ 25
     IRD Upgrade ............................................................................ 25

Troubleshooting .......................................................................

26

Specifications ............................................................................

30

Hotlines .......................................................................................

31

Installation Settings .................................................................

31

Notes ...........................................................................................

32

Summary of Contents for DSD 700

































Reviews:

No comments

Brands by name

Popular brands

Load more brands