UE 100 Serie Installation And Maintenance Instructions Manual Download Page 16

RECOMMENDED PRACTICES AND WARNINGS

United  Electric  Controls  Company  recommends  careful  consideration  of  the 
following  factors  when  specifying  and  installing  UE  pressure  and  temperature 
units.  Before  installing  a  unit,  the  Installation  and  Maintenance  instructions 
provided with unit must be read and understood. 
•  To avoid damaging unit, proof pressure and maximum temperature limits 
 

stated in literature and on nameplates must never be exceeded, even by 

 

surges in the system. Operation of the unit up to maximum temperature 

 

is acceptable on a limited basis (i.e., start-up, testing) but continuous 

 

operation must be restricted to the designated adjustable range. Excessive 

 

cycling at maximum temperature limits could reduce sensor life.

•  A back-up unit is necessary for applications where damage to a primary 
 

unit could endanger life, limb or property. A high or low limit switch is 

 

necessary for applications where a dangerous runaway condition 

 

could result.

•  The adjustable range must be selected so that incorrect, inadvertent 
 

or malicious setting at any range point cannot result in an unsafe 

 

system condition.  

•  Install unit where shock, vibration and ambient temperature fluctuations 
 

will not damage unit or affect operation. Orient unit so that moisture does 

 

not enter the enclosure via the electrical connection. When appropriate, 

 

this entry point should be sealed to prevent moisture entry.

•  Unit must not be altered or modified after shipment. Consult UE if 
 

modification is necessary.  

•  Monitor operation to observe warning signs of possible damage to unit, 
 

such as drift in set point or faulty display.  Check unit immediately.

•  Preventative maintenance and periodic testing is necessary for critical 
 

applications where damage could endanger property or  personnel.

•  For all applications, a factory set unit should be tested before use.
•  Electrical ratings stated in literature and on nameplate must not be 
 

exceeded. Overload on a switch can cause damage, even on the first 

 

cycle.  Wire unit according to local and national electrical codes, 

 

using wire size recommended in installation sheet.

•  Do not mount unit in ambient temp. exceeding published limits.

LIMITED WARRANTY

Seller  warrants  that  the  product  hereby  purchased  is,  upon  delivery,  free  from 
defects in material and workmanship and that any such product which is found 
to be defective in such workmanship or material will be repaired or replaced by 
Seller  (Ex-works,  Factory,  Watertown,  Massachusetts.  INCOTERMS);  provided, 
however,  that  this  warranty  applies  only  to  equipment  found  to  be  so  defective 
within a period of 24 months from the date of manufacture by the Seller.  Seller 
shall not be obligated under this warranty for alleged defects which examination 
discloses  are  due  to  tampering,  misuse,  neglect,  improper  storage,  and  in 
any  case  where  products  are  disassembled  by  anyone  other  than  authorized 
Seller’s  representatives.  EXCEPT  FOR  THE  LIMITED  WARRANTY  OF  REPAIR 
AND  REPLACEMENT  STATED  ABOVE,  SELLER  DISCLAIMS  ALL  WARRANTIES 
WHATSOEVER  WITH  RESPECT  TO  THE  PRODUCT,  INCLUDING  ALL  IMPLIED 
WARRANTIES  OF  MERCHANTABILITY  OR  FITNESS  FOR  ANY  PARTICULAR 
PURPOSE. 

LIMITATION OF SELLER’S LIABILITY

SELLER’S  LIABILITY  TO  BUYER  FOR  ANY  LOSS  OR  CLAIM,  INCLUDING 
LIABILITY  INCURRED  IN  CONNECTION  WITH  (I)  BREACH  OF  ANY  WARRANTY 
WHATSOEVER,  EXPRESSED  OR  IMPLIED,  (II)  A  BREACH  OF  CONTRACT,  (III) 
A  NEGLIGENT  ACT  OR  ACTS  (OR  NEGLIGENT  FAILURE  TO  ACT)  COMMITTED 
BY  SELLER,  OR  (IV)  AN  ACT  FOR  WHICH  STRICT  LIABILITY  WILL  BE  INPUTTED 
TO  SELLER,  IS  LIMITED  TO  THE  “LIMITED  WARRANTY”  OF  REPAIR  AND/OR 
REPLACEMENT AS SO STATED IN OUR WARRANTY OF PRODUCT.  IN NO EVENT 
SHALL  THE  SELLER  BE  LIABLE  FOR  ANY  SPECIAL,  INDIRECT,  CONSEQUENTIAL 
OR  OTHER  DAMAGES  OF  A  LIKE  GENERAL  NATURE,  INCLUDING,  WITHOUT 
LIMITATION, LOSS OF PROFITS OR PRODUCTION, OR LOSS OR EXPENSES OF ANY 
NATURE INCURRED BY THE BUYER OR ANY THIRD PARTY.

UE specifications subject to change without notice

.

INTERNATIONAL OFFICES

AUSTRALIA

      United Electric Controls 

      (Australia) PTY Ltd

      Unit 2, 615 Warrigal Road

      Locked Bag 600

      Ashburton, Victoria  

      3147, Australia

      Phone: 613-9567-0750 

      FAX: 613-9567-0755
BELGIUM

      United Electric Controls-Europe

      G. Van Gervenstraat 19A

      B-9120 Beveren-Waas, Belgium

      Phone: 32-37554-383 

 

      FAX: 32-37552-747
GERMANY

      United Electric Controls

      An Der Zentlinde 21

      D-64711 Erbach, Germany

      Phone: 496-062-7400

      FAX: 496-062-7501
MALAYSIA

      United Electric Controls, Far East

      No. 1-2-2, 2nd Floor 

      Jalan 4/101C

      Cheras Business Centre

      Batu 5, Jalan Cheras

      56100 Kuala Lumpur, Malaysia

      Phone: 603-9133-4122

       FAX: 603-9133-4155
RUSSIA

       United Electric Controls, Moscow 

 

       Alyabyeva str., 4-1-4

       Moscow, 121309, Russia   

 

       Phone: +7 (095) 792-88-06 

 

       FAX: +7 (095) 142-34-60

CANADA

      

EASTERN

       68 Mosley Crescent

       Brampton, Ontario

       Canada L6Y 5C8

       Phone: 905-455-5131

       FAX: 905-455-5131

       WESTERN

       148 Silver Ridge Close N.W.

       Calgary, Alberta  

       Canada T3B 3T4

       Phone:  403-247-3724

       FAX:  403-247-3724

U.S. SALES OFFICES

       United Electric Controls

       32 Highland Rd.

       South Hampton, NH  03827

       Phone: 603-394-0078

       FAX:  603-394-0175

       United Electric Controls

       28 N. Wise Ave.

       Freeport, IL  61032

       Phone:  815-235-3501

       FAX:  815-235-3847

       United Electric Controls

       1022 Vineyard Drive

       Conyers, GA 30013

       Phone: 770-483-8400

       FAX: 770-929-8716

       United Electric Controls

       5829 Grazing Court

       Mason, OH 45040

       Phone: 513-398-3175

       FAX: 513-398-3076

       United Electric Controls 

       102 Salazar Court

       Clayton, CA 94517

       Phone: 925-524-0210

       FAX: 925-524-0210

       United Electric Controls 

       27 Summit Terrace

       Sparta, NJ 07871

       Phone: 973-271-2550

       FAX: 973-729-6099

       United Electric Controls 

       12630 Summerwood Glen

       Houston, TX 77041

       Phone: 832-243-0119

       FAX: 832-243-0140

FGS3500504

1 0 0 B - 0 2

U N I T E D   E L E C T R I C  
C O N T R O L S

180 Dexter Avenue, P.O. Box 9143
Watertown, MA  02471-9143   USA
Telephone: 617 926-1000    Fax: 617 926-2568
http://www.ueonline.com

Summary of Contents for 100 Serie

















Reviews: