background image

Safety Instructions 

Definition of Symbols and Notes 
In this manual following names and signs stand for possible dangers. 
 

 

Danger

 

This Symbol stands for immediate danger threatening the life and health of persons. 
Disregarding these instructions may cause severe damage to health and even serious 
injuries. 

 

Caution 

This symbol stands for an endangering situation that may occur.  Disregarding these 
instructions may lead to slight injuries or damage to property. 

 

Note 

This symbol stands for notes, operational hints and other useful information.  They are 
convenient for exploiting the machine’s functional abilities. 

 

Danger 

Do not damage, destroy or process the power plug and cord.  Placing heavy things on the cord, 
pulling it, or bending it forcibly may damage the plug and cord and cause fire or an electrical shock. 

  

Do not plug or unplug the power cord from an outlet with a wet hand; it can result in an electrical 
shock.

     

Operate the collator with the indicated current and voltage only.   Use an exclusive outlet, as 
overloading may cause fire.

 

Do not repair, dismantle, or remodel the machine by yourself.  It may cause fire or an electrical 
shock.

 

 

Do not put your hand inside the machine.  It may make your hand caught in it and cause an injury.

 

 

Caution 

Never unplug the power cord from the outlet by gripping the cord itself.  Doing so may damage the 
cord, causing fire or injury.  

Do not put your fingers or articles in any revolving part of the machine during operation.  It may 
cause an injury.  

Do not install the machine in a humid or dusty place; excessive humidity and dust can cause fire. 

Do not use the outlet if the plug is not fixed but loose.  It may cause fire or an electrical shock. 

Do not use inflammable liquid such as gasoline, benzine, thinner, etc.  It may cause an explosion or 
fire. 

Do not place the machine near flammable materials.  It may cause fire. 

When inserting the power plug in the outlet, insert it fully into the outlet.  Otherwise, it may cause 
fire. 

When the machine body becomes hot after being used for a long time, turn off the switch and restart 
it after temporary pause.  Otherwise it may cause fire. 

In case of irregularities, such as overheating, smoking and unusual odor, turn off the power switch 
and remove the plug from the outlet.  It may cause fire or an electrical shock. 

 

When the machine will not be used for a long time, or in case of power failure, be sure to turn off the 
power switch and remove the plug from the outlet.  Otherwise, it may cause fire. 

 

- 2 - 

Summary of Contents for ST-31


















Reviews: