background image

 

EVK-MAYA-W1 - User guide 

UBX-21039658 - R01 

Board description

  

Page 12 of 22 

 

 

 

Table 4 provides a summary of the connectors and pin headers available on the evaluation board.  

Designator 

Function 

Description 

J1 

USB connector 

USB type-C connector fo

Bluetooth host interface

 

J2 

M.2 card connector 

Connector fo

M.2 card adapter

 

J3 

SDIO/M.2 card connector  Connector fo

SDIO

 or 

M.2 card adapter

 

J4/J5 

GPIOs 

Modul

GPIOs

 and interfaces 

J6 

USB/UART selection 

Pin header for USB/UART 

Bluetooth host interface

 selection 

J7 

Internal/external supply 
selection 

Pin header fo

internal or external power supply

 selection 

J8 

VIO configuration 

Pin header fo

VIO voltage configuration

 

J9 

Current measurement 

Pin header fo

current measurements

 

J10 

ANT0 

SMA connector for WLA

antenna interface

 (only on EVK-MAYA-W161) 

J11 

ANT1 

SMA connector for Bluetoot

antenna interface

 (only on EVK-MAYA-W161) 

J12 

Sleep clock enable 

Pin header to enable/disable sleep clock 

J13 

Boot configuration 

Pin header for MAYA-W

boot configuration

 

J14 

RF controls 

Pin header for RF control signals. See als

Other interfaces

 

J15 

Coexistence interface 

Pin header for coexistence interface See also 

Other interfaces

 

SW1 

Reset button 

Reset button

 

D2/D3 

LEDs 

Power supply and UART activity indicator 

LEDs

 

Table 4: MAYA-W1 evaluation board connectors 

3.3

 

Power supply configuration  

MAYA-W1  series  modules  are  supplied  with  3.3 V  (

3V3

),  1.8 V  (

1V8

),  and  selectable 

VIO

/

VIO_SD

 

voltages.  Power  supply for  the  EVB can  be provided  from the SDIO,  M.2  or  USB  host sockets  and 
internal DC-DC, or from external sources. The following power supply options are available on the EVB: 

 

SDIO or USB interfaces: The EVB is powered from the SDIO/M.2 or USB host sockets. All internal 
voltages are generated by DC-DC converters on the EVB. 

 

External sources: 3.3 V and 1.8 V voltages for the board are supplied from external power sources 
through connector J7. 

The current consumption of the MAYA-W1 module can be measured individually on each supply rail. 

3.3.1

 

Internal or external supply 

The EVB can be supplied through the host interfaces and voltages generated by internal DC-DC. To 
use internal supplies, place jumpers on pins 1-2 and 3-4 of pin header J7 (default configuration). 
To use external power sources, remove the jumpers and connect the supplies directly to the 

BRD_3V3, 

BRD_1V8

, and 

GND

 pins on J7.  

 

Figure 5: Internal/external supply (J7) 

Summary of Contents for EVK-MAYA-W1























Reviews: