Ublox EVK-MAYA-W1 User Manual Download Page 18 | Manualshive

Page: 18 / 22

background image

EVK-MAYA-W1 - User guide

UBX-21039658 - R01

Board description

Page 18 of 22

3.11

Reset button

Press the SW1 button on the EVB to reset the MAYA-W1 module. When pressed, SW1 asserts the

PDn

pin of the MAYA-W1 module to enter power down mode, while keeping the supply rails enabled.

The module is automatically reset when it exits the power down mode, which means that the firmware
must be downloaded again.

3.12

Schematics

Complete schematics for the MAYA-W1 evaluation board are available on request. For further
information,

your local u-blox support team.

«
...
16
17
18
19
20
...
»

Summary of Contents for EVK-MAYA-W1























Reviews:

No comments

Related manuals for EVK-MAYA-W1

Brand: NEJE Pages: 17

Brand: Oceanic Pages: 13

Brand: Talgil Pages: 14

Brand: Tadao Pages: 2

Brand: GEA Pages: 47

Brand: hager Pages: 4

Brand: Motorline professional Pages: 8

Brand: Swagelok Pages: 20

Brand: V-ZUG Pages: 24

Brand: Swagelok Pages: 16

Brand: Cooper Pages: 4

Brand: Trenz Electronic Pages: 21

Brand: LEGRAND Pages: 10

Brand: Danfoss Pages: 4

GA INSTRUMENTS K-1255

Brand: Vag Pages: 7

Brand: B meters Pages: 2

Brand: ModelCraft Pages: 4

Brand: Watermark Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands