background image

Regulatory Information

Regulatory Information for Canada

This Ubisense tag is approved under Industry Canada documents RSS-GEN, RSS-210 and RSS-220.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to

the following two conditions: (1) this device may not cause interference, and (2) this device must

accept any interference, including interference that may cause undesired operation of the device.

Cet appareil est conforme avec Industrie Canada RSS standard exempts de licence (s). Son

utilisation est soumise aux deux conditions suivantes: (1) cet appareil ne peut pas provoquer

d’interférences et (2) cet appareil doit accepter toute interférence, y compris les interférences qui

peuvent causer un mauvais fonctionnement du dispositif.

This Class B digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel

brouilleur du Canada, ICES-3 (B)/NMB-3(B).

CAUTION: Any changes or modifications made to the device which are not expressly

approved by Ubisense Limited could void the user's authority to operate the

equipment. This device must only be used indoors.

Regulatory Information for Europe

Hereby, Ubisense declares that this Ubisense tag is in compliance with the essential requirements

and other relevant provisions of Directive 1999/5/EC. A copy of the Declaration of Conformity for

this equipment may be obtained from:

Ubisense

St. Andrew's House

St. Andrews Road

Chesterton

Cambridge

CB4 1DL, United Kingdom

This UWB transmitter must not be installed at a fixed outdoor location or used in flying models,

aircraft and other forms of aviation.

17

Summary of Contents for Dimension4 UWB+BLE Tag





















Reviews: