Ubiquiti GigaBeam GBE-LR Quick Start Manual Download Page 4 | Manualshive

Page: 4 / 24

background image

PoE IN Port

Reset Button

White

Ready for use, not connected to Ubiquiti®
Network Management System (UNMS™). See

“UNMS Management”

.

Blue

Ready for use, connected to UNMS.

Steady Blue with
Occasional Flashing

Ready for use, unable to connect to UNMS, check
connection to UNMS server.

Quickly Flashing Blue

Used to locate a device in UNMS.

Alternating
Blue/White

Firmware upgrade in progress.

This Gigabit Ethernet port is used to connect the power and should be
connected to the LAN and DHCP server. Default IP address: 192.168.1.20.

To reset to factory defaults, press and hold the Reset button for more than 10
seconds while the device is powered on. Alternatively, the device may be reset
remotely via a Reset button located on the bottom of the Gigabit PoE Adapter.

Installation

1.

2.

GBE-LR Quick Start Guide

«
...
2
3
4
5
6
...
»

Summary of Contents for GigaBeam GBE-LR

























Reviews:

No comments

Related manuals for GigaBeam GBE-LR

Brand: Midland Pages: 64

Brand: SOUNDMASTER Pages: 72

Brand: uAvionix Pages: 31

Brand: Radio Shack Pages: 1

NS-CL01 - AM/FM Dual Alarm Clock Radio

Brand: Insignia Pages: 68

Brand: G+M Elektronik Pages: 23

Brand: Ericsson GE Pages: 16

Brand: GPX Pages: 12

FX-3 TWIN PMR 446

Brand: BRONDI Pages: 14

Brand: BTECH Pages: 81

Brand: Olywiz Pages: 2

Brand: Vertex Standard Pages: 40

RFI 150-W-D-DD-H-1

Brand: RF Innovations Pages: 30

Brand: Kienzle Automotive Pages: 44

Brand: Xact Pages: 11

Brand: jWIN Pages: 24

Brand: BK Radio Pages: 18

Brand: BK Radio Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands