Ubiquiti edgepoint r6 Quick Start Manual Download Page 21

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) 
furnished hereunder (the “Product(s)”) shall be free from defects in material and 
workmanship for a period of one (1) year from the date of shipment by UBIQUITI 
NETWORKS under normal use and operation. UBIQUITI NETWORKS’ sole and 
exclusive obligation and liability under the foregoing warranty shall be for UBIQUITI 
NETWORKS, at its discretion, to repair or replace any Product that fails to conform to 
the above warranty during the above warranty period. The expense of removal and 
reinstallation of any Product is not included in this warranty. The warranty period of 
any repaired or replaced Product shall not extend beyond its original term. 

Warranty Conditions

The above warranty does not apply if the Product:

(I) 

has been modified and/or altered, or an addition made thereto, except by 
Ubiquiti Networks, or Ubiquiti Networks’ authorized representatives, or as 
approved by Ubiquiti Networks in writing;

(II) 

has been painted, rebranded or physically modified in any way;

(III)  has been damaged due to errors or defects in cabling;

(IV)  has been subjected to misuse, abuse, negligence, abnormal physical, 

electromagnetic or electrical stress, including lightning strikes, or accident;

(V)  has been damaged or impaired as a result of using third party firmware;

(VI)  has no original Ubiquiti MAC label, or is missing any other original Ubiquiti 

label(s); or

(VII)  has not been received by Ubiquiti within 30 days of issuance of the RMA.

In addition, the above warranty shall apply only if: the product has been properly 
installed and used at all times in accordance, and in all material respects, with the 
applicable Product documentation; all Ethernet cabling runs use CAT5 (or above), 
and for outdoor installations, shielded Ethernet cabling is used, and for indoor 
installations, indoor cabling requirements are followed.

Returns

No Products will be accepted for replacement or repair without obtaining a Return 
Materials Authorization (RMA) number from UBIQUITI NETWORKS during the 
warranty period, and the Products being received at UBIQUITI NETWORKS’ facility 
freight prepaid in accordance with the RMA process of UBIQUITI NETWORKS. Products 
returned without an RMA number will not be processed and will be returned freight 
collect or subject to disposal. Information on the RMA process and obtaining an RMA 
number can be found at: www.ubnt.com/support/warranty.

19

Limited Warranty

Summary of Contents for edgepoint r6





























Reviews: