background image

BulletAC-IP67

BulletAC-IP67

Dimensions

190 x 46 mm (7.72 x 1.81")

Weight

213 g (7.51 oz)

Enclosure

Aluminum and Rubber

Processor

MIPS 74KC

Memory

DDR2 64MB

Networking Interface

(1) 10/100/1000 Ethernet Port

Antenna Connector

N-Type Connector

Max. Power Consumption

7W

Max. TX Power

22 dBm

Power Supply

24VDC, 0.3A (Minimum)*

Power Method

24V Passive PoE (Pairs 4, 5+; 7, 8 Return)

Shock and Vibration

ETSI300-019-1.4

ESD/EMP Protection

±24kV Contact / Air

Operating Temperature

-40 to 70° C

(-40 to 158° F)

Operating Humidity

5 to 95% Noncondensing

Weatherproofing

IP67

Certifications

CE, FCC, IC

* Not included with the BulletAC-IP67.

Operating Frequency (MHz)

US/CA

2400 - 2483.5

U-NII-1

5150 - 5250

U-NII-2A

5250 - 5350

U-NII-2C

5470 - 5725

U-NII-3

5725 - 5850

Worldwide

2400 - 2483.5

5150 - 5875

Safety Notices

1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.

WARNING:

 Do not use this product in location that can be submerged by water.

WARNING:

 Avoid using this product during an electrical storm. There may be a remote

risk of electric shock from lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current requirements indicated

on the manufacturer’s label. Connection to a different power source than those specified may
result in improper operation, damage to the equipment or pose a fire hazard if the limitations are
not followed.

BulletAC-IP67 Quick Start Guide

Summary of Contents for Bullet AC-IP67












Reviews: