12
Klokregeling / Control unit / Bedienmodul / Contrôle digital
Perform the following actions for this (see
1
&
13
):
• Press return
2
as many times as necessary to get to the
main screen
• Press
1
. ‘Main Menu’ opens
• Select ‘Installer’ by turning
1
• Press
1
. ‘Installer’ opens
• Turn
1
to select the desired appliance
1
• Press
1
to confirm the desired appliance (or select the
choice HRV appliance if only one appliance is connected)
• Select ‘Device settings’ by turning
1
• Press
1
. ‘Device settings’ opens
•
Select ‘Airflow 0 (Holiday)’ by turning
1
Take note!
‘Airflow 0 (Holiday)’ refers to ventilation mode
.
‘Airflow 1 (
Reduced)’ refers to ventilation mode
.
‘Airflow 2 (Normal)’ refers to ventilation mode
.
‘Airflow 3 (High)’ refers to ventilation mode
.
•
Set Airflow 0 (Holiday) by turning
1
• Press
1
to confirm the set value for Airflow 0 (Holiday)
You can set debit 1 through 3 in the same manner as descri-
bed above for Airflow 0 (Holiday).
Take note!
You cannot feed in a value, lower than
value of a lower Airflow position, for a higher (Airflow
Holiday < Airflow Reduced < Airflow Normal < Airflow
High).
4.8 Retrieving settings
You can retrieve the current settings from the Control unit.
• Press return
2
as many times as necessary to get to the
main screen
• Press
1
. ‘Main Menu’ opens
• Turn
1
to select the desired appliance
• Press
1
to confirm the desired appliance (or select the
choice HRV appliance if only one appliance is connected)
• Select ‘Device information’ by turning
1
• Press
1
. ‘Device information’ opens
• Turn
1
to display the desired information
Take note!
You can look at, but not change, the set-
tings via the info menu.
4.9 Factory settings connected device
A device has been connected to the Control unit. It is possible
to set back all this device’s settings to the factory settings.
Perform the following actions for this (see
1
):
• Press return
2
as many times as necessary to get to the
main screen
• Press
1
. ‘Main Menu’ opens
• Select ‘Installation Settings’ by turning
1
• Select ‘Installer’ by turning
1
• Press
1
. ‘Installer’ opens
• Select ‘Factory setting’ by turning
1
• Press
1
. ‘Factory setting’ opens
• Turn
1
to select the option ‘yes’
• Press
1
to confirm restoring the factory setting
• The settings are put back to the factory settings.
• Selecting factory setting will restore all step numbers to
the original factory setting. All fault messages will be de-
leted as well
5 Maintenance
5.1 General maintenance
Careful!
Clean the screen with a soft cloth.
Careful!
Never apply water and/or (cleaning) liquid to
the screen.
5.2 Cleaning or replacing filter
5.2.1 Filter notification
The filters in the device, connected to the Control unit, should
be cleaned or replaced when the text ‘FILTER’ appears on the
Control unit’s display (see
8
).
5.2.2 Removing, cleaning or replacing filters
Consult the manual of the device connected to the Control unit
for removing filters.
5.2.3 Re-setting filter notification
You can reset the filter notification after you have cleaned or
replaced the filter (or the filters). For this you press the return
button
1
for at least five seconds (see
1
&
10
).
Press return
2
to get to the main screen.
The text filter on the Control unit’s display disappears.
6 Dismantling
Warning!
You are not permitted to dismantle the
Control unit or parts of the Control unit by yourself.
This may only be done by a maintenance mechanic
approved by Ubbink.
7 Repair
Warning!
You are not permitted to open or repair the
Control unit or parts of the Control unit by yourself.
This may only be done by a maintenance mechanic
approved by Ubbink.
8 Environment
Take note!
The Control unit may not be removed as
unsorted urban waste, but should be treated separately.
Take note!
Make enquiries within your own region,
where the Control unit can be handed in when use has
