background image

20

  15. To prevent steering pump failure and oil overheating while 
driving, it is not recommended to hold the steering wheel in extreme 
positions for more than 20 sec.
  16. Use only the recommended lubricants and special-purpose 
fluids specified in the warranty and service book.
  17. Do not start the engine if the low-voltage wires are installed 
improperly to ignition coils.
 

18. When using a lubrication gun with nozzle unscrewed, remove 

the spring and the ball to avoid their falling into the units containing 
liquid lubricants.
  19. When the tail gate of your motor vehicle is opened, other 
traffic participants cannot see the rear lighting devices. Prior to 
opening the T-gate, place a warning triangle on the road as per 
GOST R 41.27-99.
  20. The long-term and fail-safe operation of the motor vehicle 
depends on how accurately you observe the requirements stipulated 
in this Manual.
 

21. For tightening torques for main threaded joints, see Appendix 

2 to this Manual.
  22. The Manufacturer constantly works on improving the 
construction of its motor vehicles, and therefore the latest design 
changes, which do not affect performance, may be absent from the 
present edition of the Manual.

Summary of Contents for HUNTER 315195









































































































































Reviews: