background image

18

revised 09/09

Smog-Hog

SG Series Model

teStinG tHe PoWer PacK 

     1.  connect ac cable to the power pack connectors 5 

and 6 with the ground wire secured to the ground 

stud on the power pack. 

     2. connect ac cable plug to wall outlet. 
     3.  Measure high voltage with high voltage probe at 

the connectors “ionizer #8” and “collector #7”, 

refer to high voltage specifications. 

     4. Disconnect ac cable plug from the wall outlet. 
     5.  replace power pack if high voltage measurements 

are above or below high voltage specifications.

    

7.  if there is an arcing condition, determine the 

problem and repair. 

    

8.  Disconnect ac cable plug from the wall outlet. 

   Refer to Step 2 “Ionizer Conditions Causing Failure” 

   Parts should be replaced as required. 

   teStinG coLLector ceLL 

     1.   Select one unicell to be tested. 
     2.  connect one high voltage wire to the collector cell 

contact spring and to the power pack connector 

identified as “collector #7”. 

     3.  connect the other high voltage wire (use as a 

ground wire) to the metal frame of the unicell cell 

and to the ground stud on the power pack. 

     4.  ac cable should be connected to the power pack 

connectors 5 and 6 with ground wire secured to 

the ground stud on the power pack. 

     5. connect ac cable plug to the wall outlet. 
     6.  Measure high voltage with the high voltage probe 

at the contact spring cell. collector cell voltage 

should be 5.0 to 7.5 KVDC, not to exceed 7.5 

KVDc. the collector cell will not maintain high 

voltages above 7.5 KVDc. the collector cell 

will continuously arc. usually this condition is 

caused by a power pack above the “High Voltage 

Specifications.” the power pack should be 

replaced. 

     7.  if there is an arcing condition, determine the 

problem and repair. 

     8.  Disconnect ac cable plug from the wall outlet. 
 

  Refer to Step 2 “Collector Cell Conditions Causing 

Failure”. 

   unicell may not be within high voltage specifications, 

even though manually cleaned, due to the service “age” 

of the unicell. the unicell should be replaced.  

   Parts should be replaced as required. 

Figure 19

Power Pack Input/Output Connections

Summary of Contents for SMOG-HOG SG SERIES

































Reviews: