background image

INSPECTION:

Carefully unpack and inspect your HHP-310  for shipping damage.  Each machine is tested and
inspected before shipping.  Any shipping damage incurred is the responsibility of the carrier.  You
should notify the carrier immediately if you notice damage to the box or to the machine or parts

.

CLEANING SOLUTIONS:

We recommend liquid cleaning chemicals, such as our Magic Fabric Cleaner.  Powder chemicals
may be used, but unless mixed very thoroughly they could cause a build-up in the pump, lines,
heat exchanger and/or quick disconnects.  Any problem caused by a chemical build-up is not
covered by warranty.  Use a neutral cleaner with a pH between 6 and 9 to avoid premature wear
of the pump, seals, and/or other components.  Damage caused by the use of strong chemicals is
not covered by the warranty.

MAINTENANCE:

For optimum performance flush the machine with clear water at the end of each working day.
Once a month, minimum, run a flushing compound through the machine to break up any mineral
or chemical build-up that may have formed.  U.S. Products’  “X-1500” is recommended.  The
vacuum motor, pump motor, and the pump do not require any scheduled maintenance; however,
the motors may require replacement brushes after 1000 - 1500 hours, and the pump and bypass
valve may require rebuild kits after 1000 - 1500 hours, typically (refer to machine part list for
numbers).  Clean the body with an all-purpose detergent, and protect it with an automobile
interior polish.  Lubricate the wheels, castors, and quick disconnects with an all purpose silicone
spray.

PARTS AND SERVICE:

Repairs, when required, should be performed by your authorized distributor who maintains an

inventory of original replacement parts and accessories.  Call the distributor  from whom you

purchased this machine if you need parts and service.  Be sure to specify the machine model.

Have your serial number handy.

(and be sure to mail your warranty card)

Serial Number: __________________
 Model: HHP-310
Purchase Date:
_____________
Write the name and phone number of your
distributor:
_____________________________________
_____________________________________

Summary of Contents for HHP-310









Reviews: