background image

SKU 93663     

For technical questions please call 1-800-444-3353

   Page 5

Working with the Rechargeable Battery

LED Functions of Light and Charger: The LED’s will provide the current status
of the Charger and Battery.

1.

There is a colored indicator LED on the Work Light. When the Power Switch is in

the ON position and the battery needs to be recharged, this light will come on
and appear Red. NOTE: If the battery is completely dead, neither the LED lights
nor the indicator LED will come on.

2.

There is a colored indicator LED on the Charger. With the Work Light in the

cradle, and the Charger plugged in, this light indicates the current status of the
battery. While the battery is charging, this light will be Red. When the battery is
fully charged, this light will turn Green. The Green light will remain on, and the
battery will continue to receive a trickle charge for as long as the Charger remains
plugged in.

3.

During charging, the Indicator LED on the Work Light will turn off.

Charging the Battery:

1.

Battery packs are normally shipped with low or no charge to prevent potential

problems during shipment. Before use, you must charge your new battery pack.

NOTE: Rechargeable batteries will not reach full charge the first time they are charged.
Allow several cycles (operation followed by recharging) before the battery will be-
come fully charged.

Battery Temperature Warning:
WARNING: 
Battery explosion may cause serious personal or property injury. Charge
the battery only within a 50° to 100° temperature range. Lower temperatures may
inhibit charging. Higher temperatures increase chance of battery failure, including
explosion.

2.

Charge the battery pack only with the included charger. Use of other chargers

may cause battery failure including explosion.

3.

Ensure that the battery charger is connected to a properly grounded, circuit

breaker protected, 120 VAC power supply only.

4.

Connect the charger to the power supply, by plugging it in.

5.

Insert the Work Light into the Charger, and press the Light into place. The Work

Light should be turned Off during charging.

6.

The red LED light will come on, indicating that the battery is charging.

7.

The red LED should remain on for approximately 3 hours while the battery charges.

Once charged, the Charger LED will change to Green indicating full charge.

Summary of Contents for 93663








Reviews: