background image

SKU 66467 

For technical questions, please call 1-800-444-3353. 

Page 5

GrOUndinG

 

TO PrEVEnT 

ElECTriC SHOCK 

And dEATH FrOM 

inCOrrECT GrOUndinG 

WirE COnnECTiOn: 

Check with a qualified 

electrician if you are in doubt 

as to whether the outlet is 

properly grounded.  do not 

modify the power cord plug 

provided with the tool.  never 

remove the grounding prong 

from the plug.  do not use the 

tool if the power cord or plug 

is damaged.  if damaged, have 

it repaired by a service facility 

before use.  if the plug will not 

fit the outlet, have a proper 

outlet installed by a qualified 

electrician.

Grounded Tools: Tools with Three 

Prong Plugs

Tools marked with “Grounding Re-

1. 

quired” have a three wire cord and 

three prong grounding plug.  The 

plug must be connected to a properly 

grounded outlet.  If the tool should 

electrically malfunction or break 

down, grounding provides a low 

resistance path to carry electricity 

away from the user, reducing the risk 

of electric shock.  

(See 3-Prong Plug 

and Outlet.)

The grounding prong in the plug is 

2. 

connected through the green wire in-

side the cord to the grounding system 

in the tool.  The green wire in the cord 

must be the only wire connected to 

the tool’s grounding system and must 

never be attached to an electrically 

“live” terminal.  

(See 3-Prong Plug 

and Outlet.)

The tool must be plugged into an 

3. 

appropriate outlet, properly installed 

and grounded in accordance with all 

codes and ordinances.  The plug and 

outlet should look like those in the 

preceding illustration.  

(See 3-Prong 

Plug and Outlet.)

double insulated Tools: Tools 

with Two Prong Plugs

Tools marked “Double Insulated” do 

1. 

not require grounding.  They have 

a special double insulation system 

which satisfies OSHA requirements 

and complies with the applicable 

standards of Underwriters Labora-

tories, Inc., the Canadian Standard 

Association, and the National Electri-

cal Code.  

(See Outlets for 2-Prong 

Plug.)

Summary of Contents for 66467















Reviews: