U.S. Boiler Company V8H SERIES Installation, Operating And Service Instructions Download

Page: 10 / 96

Figure 2: Minimum Installation Clearances To Combustible Materials (Inches)

INSPECT SHIPMENT

carefully for any signs of

damage.

1. All equipment is carefully manufactured, inspected

and packed. Our responsibility ceases upon delivery

of crated boiler to the carrier in good condition.

2. Any claims for damage or shortage in shipment

must be filed immediately against the carrier by the

consignee. No claims for variances from, or shortage

in orders, will be allowed by the manufacturer

unless presented within sixty (60) days after receipt

of goods.

LOCATE BOILER

in front of final position before

removing crate. See Figures 1A thru 1D.
1. LOCATE so that vent pipe connection to chimney

will be short and direct.

2. BOILER IS SUITABLE FOR INSTALLATION

ON COMBUSTIBLE FLOOR. Boiler cannot be

installed on carpeting.

3. FOR BASEMENT INSTALLATION, provide

a solid elevated base, such as concrete, if floor is

not level, or if water may be encountered on floor

around boiler.

4. PROVIDE SERVICE CLEARANCE of at least

24” clearance from front jacket panel for servicing

and removal of front tankless heater (increase to

30" for #A54 heater). If boiler is equipped with

a rear tankless heater, provide at least 24" service

clearance on the right side of the boiler. Boiler

flueways may be cleaned either from the top

from

the right side. Provide at least 24" clearance from

either the right side of the boiler

the top of the

boiler for cleaning flueways.

5. For minimum clearances to combustible materials.

See Figure 2.

NOTICE

Clearance to venting is for single wall vent

pipe. If Type L vent is used, clearance may be

reduced to the minimum required by the vent pipe

manufacturer.

SECTION II: PRE-INSTALLATION

NOTES:

1. Listed clearances comply with American

National Standard ANSI/NFPA 31, Installation of

Oil Burning Equipment.

2. V8H Series boilers can be installed in rooms with

clearances from combustible material as listed

above. Listed clearances cannot be reduced for

alcove or closet installations.

3. For reduced clearances to combustible material,

protection must be provided as described in the

above ANSI/NFPA 31 standard.

Summary of Contents for V8H SERIES

































































































Search results

Summary of Contents for V8H SERIES

Reviews:

Related manuals for V8H SERIES

Brands by name

Popular brands

U.S. Boiler Company V8H SERIES, Installation, Operating And Service Instructions

Search results

Summary of Contents for V8H SERIES

Reviews:

Related manuals for V8H SERIES

Brands by name

Popular brands