U.S. Boiler Company ENHANCED 2 Series Installation, Operating And Service Instructions Download Page 4

Page: 4 / 60

Congratulations

on your purchase of a new ES2 boiler—designed and constructed to provide you with

years of reliable service.

•

Cast iron heat exchanger

– for reliability and durability, nothing beats a cast iron heat exchanger.

•

IQ Control™

System– the most advanced and easiest to use control available.

•

System-friendly

– built-in protection from condensation and thermal shock.

ES2™

Boiler

Vent Damper w/ Carton



4” Damper



ES23 (102284-01)



5” Damper



ES24 (102284-02)



6” Damper



ES25 & ES26 (102284-03)



7” Damper



ES27 & ES28 (102284-04)



8” Damper



ES29 (102284-05)

Circulator & Gasket Kit



Taco 007-2 (8056170)



Grundfos UP-15 (102805-02)



Grundfos Alpha (104935-01)



B & G NRF-22 (8056174)

Miscellaneous Parts Bag

Temperature/Pressure Gage; ¼” NPT

(100282-01)

Circulator Mounting Hardware Kit, 1- 1/4”

NPT (6056007) - except less circulator

Drain Valve; ¾” NPT (102802-01)

Safety Relief Valve; 30 psi (81660363)

Water Manifold (80607001)

Instruction Envelope (103779-01)

Instruction & Operation Manual

(103780-06)

Boiler Warranty Sheet (103203-01)

Boiler Warranty Card (103204-02)

What's in the crate?

IQ Control System Overview

ES2 Boiler uses a microprocessor based control system called the "IQ Control System". This "IQ Control

System" consists of an Intelligent Hydronic Control (Control) and an IQ Option Panel (Option Panel) with

optional "plug-in" IQ Option Cards (Option Card). The IQ Control System fully integrates both factory and

field installed components, simplifying installation and troubleshooting. The IQ Control System is designed

to efficiently operate the entire boiler system to save energy, installation and setup time while ensuring

adequate supply of heat and domestic hot water.

Summary of Contents for ENHANCED 2 Series





























































Search results

Summary of Contents for ENHANCED 2 Series

Reviews:

Related manuals for ENHANCED 2 Series

Brands by name

Popular brands

U.S. Boiler Company ENHANCED 2 Series, Installation, Operating And Service Instructions

Search results

Summary of Contents for ENHANCED 2 Series

Reviews:

Related manuals for ENHANCED 2 Series

Brands by name

Popular brands