background image

QUICK START GUIDE

10

USER GUIDE

Water Hookup

Water Hookup

TO PREVENT DAMAGE TO Y0UR ICE MACHINE 
AND/OR VOID YOUR WARRANTY, FOLLOW ALL 
WATER SUPPLY GUIDELINES AS LISTED BELOW.

PREPARE PLUMBING

The water valve uses a standard 1/4” (6.35 mm) 
compression fitting. U-Line recommends using accessory 
water hook up kit – part # 80-54674-00. The kit includes 
a 10’ (3 m) braided flexible water supply line and a brass 
hose fitting.

Plumbing installation must observe all state 
and local codes. All water and drain connections 
MUST BE made by a licensed/qualified plumbing 
contractor. Failure to follow recommendations 
and instructions may result in damage and/or 
harm.

Water Supply

When connecting the water supply, please note the 
following:

•  Water Mineral Content must meet the following:

 

◦ 

TDS: less than 200 ppm (mg/l)

 

◦ 

Hardness: Less than 200 mg/l (12 gpg)

•  Water supply MUST NOT be from a water 

softener. 

•  A TDS meter is included with your unit

•  Water Treatment Options

 

◦ 

TDS level of 200 ppm or higher and/or a 

hardness of 12-19 gpg can be treated by U-Line’s in-line 
water filter accessories available at u-line.com or your 
local dealer:

 

ULALINEFILTER — Standard

 

ULALINEFILTERL — Large

 

ULALINEFILTERHEAD — 3/8” NPT, initial    

  setup requires head & filter

•    Use bypass level 6

Measure Water TDS

Every Nugget Ice Machine comes with a TDS meter similar 
to the one below. The TDS meter measures the 

Total 

Dissolved Solids

 level that exists in the water supply; this 

is measured in ppm (parts per million). 

The TDS meter does not test the toxicity of 
the water and is not to be used to determine 
potability. A TDS METER CANNOT DETECT THE 
TOXINS THAT MAKE WATER UNSAFE TO DRINK. 

1.  Turn on sink faucet and let run for 30 seconds.

2.  Fill a clean glass (2 inches of water is sufficient).

3.  Remove cap from meter.

4.  Turn on meter and immerse meter into the water.

5.  Leave meter immersed for 30 seconds.

6.  Remove meter and check the readout for the TDS 

level in ppm - to save the reading, press the hold 
button. 

7.  Turn off meter, dry off, and replace cap.

CAUTION

!

CAUTION

!

TDS

ON

OFF

HOLD

PP

M

ON

OFF

HOLD

TDS

WARNING

!

ON

OFF

HOLD

TDS

PPM

Water Hookup

Nugget Ice Machines

CAUTION

!

Summary of Contents for UONP115SS01B





































Reviews: