background image

PAGE 15 OF 17 

0921 IH-9560

TECHINICAL DATA CONTINUED

NTEP AND MEASUREMENT CANADA APPROVED MODELS:

MODEL

H-9560

H-9561

Capacity

620 g

1,500 g

Readability

0.1 g

0.01 g or 0.1 g

Verification Interval e

0.1 g

0.1 g

Class

III

II

Span Calibration Mass

300 g

1.5 kg

Linearity

300 g, 600 g

1 kg, 1.5 kg

Capacity x Readability (kg)

/

1.5 x 0.00001 or 1.5 x 0.0001

Capacity x Readability (ct)

3,100 x 0.5

7,500 x 0.5

Capacity x Readability (oz)

21.870 x 0.005

52.910 x 0.005

Capacity x Readability (ozt)

19.935 x 0.005

48.225 x 0.005

Capacity x Readability (dwt)

398.7 x 0.1

964.52 x 0.01 or 964.5 x 0.1

Capacity x Readability (lb)

1.3670 x 0.0005

3.3070 x 0.0005

Capacity x Readability (grn)

9,568 x 2

23,148 x 2

Stabilization Time (s)

1

1.5

Construction

ABS housing and stainless steel pan

Draftshield

No

Calibration

User-selectable external span or linearity calibration

Tare Range

Full Capacity by subtraction

Weighing Units*

g, kg, ct, oz, ozt, dwt, lb, grn

Application Modes*

Weighing, Parts Counting, Percent Weighing, Check Weighing, Totalization,  

Density Determination, Display Hold

ypical Battery Life

80 hours

Specified Temperature Range

Class II: 50°F to 86°F  

Class III: 50°F to 104°F

Storage Conditions

-4°F to 131°F at 10% to 90% relative humidity, non-condensing

Communication

RS232, USB Host, USB Device, Ethernet or Bluetooth**  

(all available as accessory)

Display Type

Backlit LCD: 6-digit 7-segment with white LED backlight

Display Size

0.78 in / 20 mm digits

Pan Size (W x D)

Ø120 mm / 4.7 in

170 x 140 mm / 6.7 x 5.5 in

Scale Dimensions  

(W x D x H)

202 x 224 x 54 mm / 8 x 8.8 x 2.1 in

Shipping Dimensions 

(W x D x H)

300 x 250 x 86 mm / 11.8 x 9.8 x 3.4 in

Net Weight

2.2 lb / 1 kg

Shipping Weight

3.3 lb / 1.5 kg

 * Available Weighing Units and Application Modes vary by local regulations.

 ** Bluetooth kit is only available in certain regions according to the local regulations.

Summary of Contents for SCOUT H-9560


















Reviews: