background image

PAGE 1 OF 18 

0323 IH-1024

1-800-295-5510

uline.com

MANUAL CARTON STAPLER

H-1024, H-1025

H-1026

SPECIFICATIONS

SAFETY

Dimensions (L x H x W)

15 x 11½ x 4½"

Weight (Without Fasteners)

3.75 lb.

H-1025/H-1026 Staple Specification

S-289 C58 Stick and/or S-1396 C34 Stick

H-1024 Staple Specification

S-1397 A58 Stick

Staple Capacity

100 Staples

• Read the manual and understand all safety 

instructions before operating the stapler. If you have 
questions, contact Uline at 1-800-295-5510.

• Always wear protective equipment; e.g., safety 

glasses, hearing protection and head protection.

• Do not place your hand or any other body part in 

the staple clinching area.

• Never point the stapler at yourself or anyone else.

• Ensure that anyone in the vicinity wears safety 

protection.

• To prevent accidental injuries, never place a hand 

or any other body part in the staple clinching area 
or adjustment window.

• Always handle the stapler with care. Never pull the 

trigger unless stapler is ready for operation.

• Check and replace any damaged or worn 

components on the stapler.

Para Español, vea páginas 7-12.

Pour le français, consulter les pages 13-18.

Summary of Contents for H-1024



















Reviews: