U-Line 1224FZR User Manual & Service Manual Download

Page: 58 / 69

USER GUIDE

Control Operation - Service 1

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE •

SERVICE

Control Operation - Service

UI BUTTON LAYOUT

Hidden Button

-Accesses Service Menu
-No LED directly above. All LEDs turn on with button
activation except #7.

Up Button

-Increases temperature
-Navigates through service menu
-LED activated with button activation.

Down Button

-Decreases temperature
-Navigates through service menu
-LED activated with button activation

Light Button

-Activates light for 3 hours on select models
-Used to select items in service menu
-LED activated with button activation

Power Button

-Turns unit off/on
-LED activated with button activation (only turning unit
off)

Clean Button

-Activates Clean Cycle on CLR models
-LED activated with button activation

LED

-No button

Summary of Contents for 1224FZR






































































Search results

Summary of Contents for 1224FZR

Reviews:

Related manuals for 1224FZR

Brands by name

Popular brands

U-Line 1224FZR, User Manual & Service Manual

Search results

Summary of Contents for 1224FZR

Reviews:

Related manuals for 1224FZR

Brands by name

Popular brands