background image

 

EVK-R6 and EVK-L6 - User guide 

UBX-21035387 - R03 

Appendix

  

Page 22 of 27 

C1-Public 

 

 

C

 

Examples of AT commands 

For  the  complete  description  and  syntax  of  the  AT  commands  supported  by  LARA-R6  /  LARA-L6 
series modules, see the u-blox AT commands manual 

[1]

. 

C.1

 

Define the initial default bearer for connectivity 

To change the PDN settings for the initial default EPS bearer established during LTE attach, edit the 
<cid>=1 PDN by means of the +CGDCONT AT command.  

Command sent by DTE (user) 

DCE response (module) 

Description 

AT+COPS? 

+COPS: 2 
OK 

The module is not registered. 

AT+CEREG=2;+CGEREP=1,1 

OK 

Enable a set of registration URCs. 

AT+CGDCONT? 

+CGDCONT: 1,"IPV4V6","","0.0.0.0 
0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",
0,0,0,2,0,0,0,0,0,0 
OK 

Read IP type and APN for EPS attach 
bearer. 

AT+CGDCONT=1,"IPV4V6","broadband"  OK 

Set the APN name ("broadband" for 
example) and the PDP type ("IPV4V6" 
for example) for EPS attach bearer. 

AT+COPS=0 

OK 
 
+CEREG: 1,"0001","01a2d001",7 
+CGEV: ME PDN ACT 1 

Trigger a network registration and wait 
for attach complete. 

The same procedure can also be applied for the PDP context associated with <cid>=1 in 2G and 3G 
RAT. During the LTE attach, the initial default EPS bearer is automatically activated by the network, 
while in 2G and 3G RAT, it is necessary to manually activate the PDP context by means of +CGACT AT 
command. 

Command sent by DTE (user) 

DCE response (module) 

Description 

AT+CGACT=1,1 

OK 

Activate the PDP context associated 
with <cid>=1. 

It is possible to verify the status of the initial default EPS bearer or a PDP context by the means of the 
+CGDCONT and +CGCONTRDP AT commands. 

Command sent by DTE (user) 

DCE response (module) 

Description 

AT+CGDCONT? 

+CGDCONT: 1,"IP","default.mnc321.
mcc654.gprs","192.168.20.6",0,0,0
,2,0,0,0,0,0,0 
OK 

Read IP type and APN for EPS attach 
bearer. 
Context <cid>=1 has IP type "IP" and 
APN "default.mnc321.mcc654.gprs". 

AT+CGCONTRDP=1 

+CGCONTRDP: 1,5,"default.mnc321.m
cc654.gprs","192.168.20.6.255.255
.255.0","192.168.20.1","185.215.1
95.114","","","",0,0,1500,0,0 
OK 

Read context <cid>=1 dynamic 
parameters. 
<cid>=1 is currently active with IPv4 
address 192.168.20.6/24, gateway 
192.168.20.1 and DNS server 
185.215.195.114. 

C.2

 

Data connection using internal TCP/IP stack 

The internal TCP/IP stack is automatically mapped, configured, and activated to the initial default 
EPS  bearer  established  during  LTE  attach  or  to  the  first  activated  PDP  context  in  2G  or  3G  RAT. 
Consequently  the  +UPSD  and  +UPSDA  commands  are  no  longer  required  to  perform  these  tasks 
manually. 

 

Summary of Contents for EVK-R6




























Reviews: