background image

EVK-7 / EVK-8 / EVK-M8 User Guide 

 

UBX-14002502 - R10

 

Early Production Information

 

Device description

 

 

 

Page 12 of 25

 

4.3.9

 

LED 

On the front panel of the unit, a single blue LED shows the time pulse 1 signal. The LED starts 
flashing one pulse per second during a GNSS fix. If there is no GNSS fix, the LED will only light, without 
flashing. 

4.3.10

 

Backup Battery 

There is a  backup battery  in  the evaluation unit.  This is necessary  to store orbital information 
between operations and to enable faster start-up. It is a RENATA 3.0 V Li / MnO

²

 battery of the type 

CR2450. The battery has a rated capacity of 540 mA. The battery operating temperature range is -
40° C to +85° C. 

In case the built-in backup battery runs low or empty after a long storage period, purchase the above 
described battery for replacement (refer to the section 10 for battery replacement guidelines).  

 

 

CAUTION! RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE 
OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS! 

4.3.11

 

GNSS Configuration 

The EVK-7 and EVK-8 supports GPS, QZSS and GLONASS.  The EVK-M8N/C and EVK-
M8MEVA/EVK-M8QEVA supports GPS, Galileo,

 

QZSS, GLONASS, and BeiDou.  

The GNSS to be used can be configured on u-center (View 

 Messages View then UBX-CFG-GNSS). 

For more information, refer to the 

u-center User Guide  [21],  the  u-blox  7  Receiver Description 

including Protocol Specification [9] and u-blox 8 / u-blox M8 Receiver Description including Protocol 
Specification [20]. 

4.3.12

 

RTC Configuration (EVK-7EVA and EVK-M8MEVA) 

The EVK-7EVA and EVK-M8MEVA include the EVA-7M or EVA-M8M GNSS receiver with an external 
RTC. By default, the EVA-7M or EVA-M8M module is not running in single crystal mode. The 
EVK-7EVA and EVK-M8MEVA evaluation kits can be set to single crystal mode by using the 
configuration string described in the EVA-7M Hardware Integration Manual [8] and the EVA-8M / 
EVA-M8M Hardware

 Integration Manual [18].  

 

Applying the configuration string results in a permanent change and cannot be reversed. The 
current consumption is significantly higher in single crystal mode. For more information see the 
EVA-7M Data Sheet [5], EVA-8M Data Sheet [25] and the EVA-M8 Data Sheet [13]. 

 

Summary of Contents for EVK-8


























Reviews: