background image

 

EVK-7 / EVK-8 / EVK-M8 - User Guide 

UBX-14002502 - R10 

Early Production Information

 

Page 2 of 25 

 

 

 

Document Information 

Title 

EVK-7 / EVK-8 / EVK-M8 

Subtitle 

User Guide 

Document type 

User Guide 

Document number 

UBX-14002502 

 

Revision and date 

R10 

3-Sep-2018 

Document status 

Early Production Information 

 

European Union regulatory compliance 

EVK-7P, EVK-M8N, EVK-M8C, EVK-M8MEVA, EVK-M8QEVA and EVK-8N comply with all relevant requirements for RED 
2014/53/EU. The relevant Declaration of Conformity (DoC) is available a

www.u-blox.com

 within Support > Product 

resources > Conformity Declaration. 

 

This document applies to the following products: 

Product name 

Type number 

Hardware version  ROM/FLASH version 

EOL/PCN reference 

EVK-7N 

EVK-7N-0-000 

ROM 1.00 Flash FW1.00 

UBX-17049159 (EOL) 

EVK-7C 

EVK-7C-0-000 

ROM 1.00, 1.01, Flash FW1.00 

UBX-17049159 (EOL) 

EVK-7P 

EVK-7P-0-000 

ROM 1.00 PPP1.01, Flash FW1.00 

N/A 

EVK-7EVA 

EVK-7EVA-0-000 

ROM 1.00 

UBX-17049159 (EOL) 

EVK-M8N 

EVK-M8N-0-01 

Flash SPG 3.01 

N/A 

EVK-M8C 

EVK-M8C-0-01 

Flash SPG 3.01 

N/A 

EVK-M8MEVA 

EVK-M8MEVA-0-01 

ROM SPG 3.01 

N/A 

EVK-M8QEVA 

EVK-M8QEVA-0-00 

ROM SPG 3.01 

N/A 

EVK-8N 

EVK-8N-0-00 

ROM SPG 3.01 

N/A 

 

 

u-blox or third parties may hold intellectual property rights in the products, names, logos and designs included in this 
document. Copying, reproduction, modification or disclosure to third parties of this document or any part thereof is only 
permitted with the express written permission of u-blox. 
The information contained herein is provided “as is” and u-blox assumes no liability for its use. No warranty, either express or 
implied, is given, including but not limited to, with respect to the accuracy, correctness, reliability and fitness for a particular 
purpose of the information. This document may be revised by u-blox at any time without notice. For the most recent 
documents, visit www.u-blox.com.  
Copyright © u-blox AG. 

Summary of Contents for EVK-8


























Reviews: