background image

- 69 - 

 

3.6.  Save & Exit 

 

 

 

Save Changes and Reset

To save the changes, select this field and then press <Enter>. A dialog box will 
appear. Select “Yes” to reset the system after saving all changes made. 

 

 

Discard Changes and Reset

To discard the changes, select this field and then press <Enter>. 
A dialog box will appear. 
Select “Yes” to reset the system setup without saving any changes. 

 

 

Restore Defaults

To restore and load the optimized default values, select this field and then press 
<Enter>. A dialog box will appear. Select 

“Yes” to restore the default values of all the 

setup options. 

 

 

Save as User Defaults

To save changes done so far as user defaults, select this field and then press 
<Enter>. A dialog box will appear. Select 

“Yes” to save values as user default. 

 

 

Restore User Defaults

To restore user default to all the setup options, select this field and then press 
<Enter>. A dialog box will appear. Select “Yes” to restore user default. 

 

 

Launch EFI Shell from file system device

Attempts to launch EFI shell application (Shellx64.efi) from one of the available file 
system devices. 

Summary of Contents for POP-650-i






































































































































Reviews: