background image

4

 

 

1. Basic safety  instructions

 

 
 

 

1.1 

 Warnings and symbols in this manual

 

 

 

Danger!  Points out that serious or even fatal injuries may result if not followed. 

Caution!  Points out that injuries may result if not followed.

 

Notice! 

Points out that damage to the machine or other equipment may result if not followed

.

 

 
 

 

1.2 

 Principle of intended use

 

 

 

Danger!   1.2.1  The stone cutoff saw is designed exclusively for wet sawing of building blocks made of 

mineral materials. Sawing of wood or metal is prohibited!

 

The manufacturer/supplier is not liable for damages resulting from improper use. 

Compliance with the operating manual and observation of inspection and service

 

requirements are essential components of proper use

.

 

 

 

1.2.2  

Use the machine only in correct working order and for its intended purpose. The operator 
must follow the instructions in the operating manual and be fully aware of the safety 
requirements and hazards posed by the machine. In particular, any faults that may 
compromise safety must be repaired immediately.

 

 
 
 

 

1.3 

 Organisational measures

 

 

 

1.3.1   

Always keep the operating manual readily available at the location where the machine is used!

 

 

 

Danger! 1.3.2    lnstruct users to observe supplements to the operating manual as weil as all generally 

applicable legal and other mandatory regulations on accident prevention and 
environmental protection!

 

 

 

Obligations of this nature may also relate to the use of dangerous substances, for 
example, or the wearing of personal protective equipment or to road traffic regulations.

 

 

 

Danger!  1.3.3  Personnel assigned to work with the machine must have read the

 

operating instructions and, in particular, the chapter on safety before beginning work. 
Reading the manual for the first time when working on the machine is too late.

 

This applies especially to persons who work on the machine only occasionally, such as 
those performing set-up and maintenance.

 

Summary of Contents for TME700P



















Reviews: