TFP682
Page 7 of 10
Upright and Pendent Sprinklers
The Poly-Stainless Series TY-B and
TY-FRB Upright and Pendent Sprin-
klers must be installed in accordance
with the following instructions:
Step 1A.
Upright sprinklers must be
installed in the upright position, and
pendent sprinklers are to be installed
in the pendent position.
Step 2A.
With pipe thread sealant
applied to the pipe threads, hand
tighten the sprinkler into the sprinkler
fitting.
Step 3A.
Tighten the sprinkler into the
sprinkler fitting using only the W-Type
6 Sprinkler Wrench, refer to Figure 10.
With reference to Figures 1, 2, 3, and 4,
apply the W-Type 6 Sprinkler Wrench to
the sprinkler wrench flats.
Recessed Pendent Sprinklers
The Poly-Stainless Series TY-B and
TY-FRB Recessed Pendent Sprinklers
must be installed in accordance with
the following instructions:
Step 1B.
After installing the Style 10
or 40 Mounting Plate, as applicable,
over the sprinkler threads and with
pipe sealant applied to the sprinkler
threads, hand tighten the sprinkler into
the sprinkler fitting.
Step 2B.
Tighten the sprinkler into the
sprinkler fitting using only the W-Type
7 Recessed Sprinkler Wrench, refer to
Figure 11. With reference to Figures
1, 2, 3, and 4 apply the W-Type 7
Recessed Sprinkler Wrench to the
sprinkler wrench flats.
Step 3B.
After the ceiling has been
installed or the finish coat has been
applied, slide the Style 10 or 40 Closure
over the sprinkler and push the Closure
over the Mounting Plate until it comes
in contact with the ceiling mounting
surface.
Horizontal Sidewall Sprinklers
The Poly-Stainless Series TY-B and
TY-FRB Horizontal Sprinklers must be
installed in accordance with the follow-
ing instructions:
Step 1C.
Horizontal sprinklers must
be positioned in the horizontal position
with their centerline of waterway per-
pendicular to the back wall and parallel
to the ceiling. The word “TOP” on the
deflector is to face towards the ceiling.
Step 2C.
With pipe thread sealant
applied to the sprinkler threads, hand
tighten the sprinkler into the sprinkler
fitting.
Step 3C.
Tighten the sprinkler into the
sprinkler fitting using only the W-Type
6 Sprinkler Wrench, as shown in Figure
10. Apply the W-Type 6 Sprinkler
Wrench to the wrench flats shown in
Figure 5 and Figure 6.
Recessed Horizontal Sidewall
Sprinklers
The Poly-Stainless Series TY-B and
TY-FRB Recessed Horizontal Sidewall
Sprinklers must be installed in accor-
dance with the following instructions:
Step 1E.
Recessed horizontal sidewall
sprinklers are to be positioned in the
horizontal position with their centerline
of waterway perpendicular to the back
wall and parallel to the ceiling. The
word “TOP” on the deflector is to face
towards the ceiling.
Step 2E.
After installing the Style 10
Mounting Plate over the sprinkler
threads and with pipe thread sealant
applied to the sprinkler threads, hand
tighten the sprinkler into the sprinkler
fitting.
Step 3E.
Tighten the sprinkler into the
sprinkler fitting using only the W-Type
7 Recessed Sprinkler Wrench, refer to
Figure 11. Apply the W-Type 7 Sprinkler
Wrench to the wrench flats shown in
Figure 5 and Figure 6.
Step 4E.
After the wall has been
installed or the finish coat has been
applied, slide the Style 10 Closure over
the sprinkler and push the Closure over
the Mounting Plate until it comes in
contact with the wall mounting surface.
3
4
5
6
1
2
*
*
*
Temperature rating is
indicated on Deflector
Sealing
Assembly
Compression
Screw
Bulb
Deflector
Button
Frame
1/2"
NPT
WRENCH
FLATS
7/16"
(11,1 mm)
NOMINAL
MAKE-IN
1-1/2"
(38,1 mm)
2-3/16"
(55,6 mm)
ESCUTCHEON
PLATE SEATING
SURFACE
DEFLECTOR
HAT
1-13/16"
(46,0 mm)
9/16"
(14,3 mm)
CENTERLINE
OF SPRINKLER
WATERWAY
2-7/8" DIA.
(73,0 mm)
STYLE 10
RECESSED
ESCUTCHEON
-
-
-
-
-
-
6
4
2
5
3
1
FIGURE 6
POLY-STAINLESS SERIES TY-FRB QUICK RESPONSE HORIZONTAL
SIDEWALL (TY3331) 5.6 K-FACTOR 1/2 INCH NPT SPRINKLERS
