Tyco ACC-1 Manual Download Page 11

Page: 11 / 38

TFP1090

Page 11 of 26

Step 10A.

While holding the plunger

of the Automatic Drain Valve

depressed, open the Accelerator

Control Valve one-quarter turn and

allow the water in the Accelerator

piping to blow out. After water spray

stops discharging, close the Accel-

erator Control Valve and then release

the plunger.

Step 10B.

Slowly remove the Vent

Plug located in the front of the Accel-

erator Cover and bleed off any resid-

ual air pressure in the Differential

Chamber.

Step 10C.

Unscrew (counter-clock-

wise rotation) the knurled Reset

Knob at the front of the Accelera-

tor until it resists further turning. A

click, which is the sound of the Lever

snapping back into the Set Position,

may be heard. Screw the Reset Knob

back in until it is finger tight.

NOTICE

Do not wrench on the Reset Knob,

since damage may result. The Reset

Knob will turn with finger torque only.

Step 10D.

Replace the Vent Plug.

Step 10E.

Verify that the system air

pressure has returned to normal.

Step 10F.

Using a watch, note the

time for the pressure in the Differen-

tial Chamber of the Accelerator to

increase to 0,7 bar after the Accel-

erator Control Valve is opened. The

time should be within the range of

values indicated in Table C for opti-

mum performance of the Accelerator.
If the time to pressurize the Differen-

tial Chamber to 0,7 bar is not within

the range of values given in the Table

C, then the Accelerator Control Valve

should be closed and the corrective

procedure described in the Care and

Maintenance Section of ACC-1 Tech-

nical Data Sheet TFP1112 should be

followed.

Step 10G.

When the air pressure

in the Differential Chamber of the

Accelerator is equal to that in the

system, then the Accelerator is set

and ready for service.

Step 10H.

Close the Accelerator

Control Valve and then slowly open

the Low Body Drain Valve in the

trim, to bleed off any excess water

trapped above the Dry Pipe Valve

Clapper. Close the Low Body Drain

Valve, return system pressure to its

normal value, and then re-open the

Accelerator Control Valve.

Step 11.

Partially open the Main Con-

trol Valve. Slowly close the Main Drain

Valve as soon as water discharges from

the drain connection.
Verify that there is not any water dis-

charging from the Automatic Drain

Valve.

The absence of water discharging from

the Automatic Drain Valve is an indica-

tion of a properly set water seat within

the M

del

DPV-1 Dry Pipe Valve. If

water is discharging, see the Care and

Maintenance section under the Auto-

matic Drain Valve Inspection to deter-

mine/correct the cause of the leakage

problem.
If there are no leaks, the Model

DPV-1

Dry Pipe Valve is ready to be placed

in service and the Main Control Valve

must then be fully opened.
After setting a fire protection system,

notify the proper authorities and advise

those responsible for monitoring pro-

prietary and/or central station alarms.

Step 12.

Once a week after a valve is

reset following an operational test or

system operation, the Low Body Drain

Valve (and any low point drain valves)

should be partially opened (and then

subsequently closed) to relieve drain-

back water. Continue this procedure

until drain-back water is no longer

present.

Care and

Maintenance

The following procedures and inspec-

tions should be performed as indicated,

in addition to any specific require-

ments of any authority having jurisdic-

tion. Impairments must be immediately

corrected.
The owner is responsible for the

inspection, testing, and maintenance of

their fire protection system and devices

in compliance with this document, as

well as with the applicable standards

of any authority having jurisdiction. The

installing contractor or product manu-

facturer should be contacted relative to

any questions.
Automatic sprinkler systems are rec-

ommended to be inspected, tested,

and maintained by a qualified Inspec-

tion Service.

NOTICE

The operational test procedure and

waterflow pressure alarm test pro-

cedure will result in operation of the

associated alarms. Consequently,

notification must first be given to the

owner and the fire department, central

station, or other signal station to which

the alarms are connected.
Before closing a fire protection system

Main Control Valve for maintenance

work on the fire protection system

that it controls, obtain permission to

shut down the affected fire protection

systems must first be obtained from the

proper authorities and notify all person-

nel who may be affected by this deci-

sion must be notified.

Annual Operation

Test Procedure

Proper operation of the Model DPV-1

Dry Pipe Valve (that is, opening of the

Model DPV-1 Dry Pipe Valve during

a fire condition) should be verified at

least once a year as follows:

Step 1.

If water must be prevented

from flowing beyond the riser, perform

the following steps:
•  Close the Main Control Valve.
•  Open the Main Drain Valve.
•  Open the Main Control Valve one turn

beyond the position at which water

just begins to flow from the Main

Drain Valve.

• Close the Main Drain Valve.

Step 2.

Open the system’s Inspector’s

Test Connection.

Step 3.

Verify that the Model DPV-1

Dry Pipe Valve has operated, as indi-

cated by the flow of water into the

system and that all waterflow alarms

operate properly.

Step 4.

Close the system’s Main Con-

trol Valve.

Step 5.

Reset the Model DPV-1 Dry

Pipe Valve in accordance with the Valve

Setting Procedure.
The inside of the valve is recommended

to be inspected at this time and prior

to resetting the Model DPV-1 Dry Pipe

Valve. See Steps 2 to 5 in the Inspec-

tion Procedure section on the Auto-

matic Drain Valve for instructions on

the inspection of the Clapper Facing.

Periodic Waterflow Alarm

Test Procedure

Testing of the system waterflow

alarms should be performed periodi-

cally based on the requirements of the

authority having jurisdiction. To test the

waterflow alarm, place the Three-way

Alarm Test Valve in the “Test” posi-

tion or open the Standard Alarm Test

Valve, as applicable, which will allow

a flow of water to the Waterflow Pres-

sure Alarm Switch and/or Water Motor

Alarm. Upon satisfactory completion

of the test, place the Three-way Alarm

Test Valve in the “Open” position or

close the Standard Alarm Test Valve,

as applicable.

Water Pressure

Inspection Procedure

The Water Pressure Gauge is to be

inspected periodically based on the

requirements of the authority having

jurisdiction to ensure that normal

system water pressure is being

maintained.

Summary of Contents for ACC-1







































Search results

Summary of Contents for ACC-1

Reviews:

Related manuals for ACC-1

Brands by name

Popular brands

Tyco ACC-1, Manual

Search results

Summary of Contents for ACC-1

Reviews:

Related manuals for ACC-1

Brands by name

Popular brands