Tyco ACC-1 Manual Download

Page: 27 / 38

Appendix A of TFP1090 (07/2020)

Summary Instructions (if problems occur, consult full document)

DN65 and DN80, Model DPV-1 Dry Pipe Valve with Three-Way Alarm Test Valve,

without Model ACC-1 Accelerator

426 mm

185 mm

422 mm

367 mm

I. Normal Conditions

• The Main Control Valve (A) is opened

and locked.

• The sprinkler system is filled with air

and is pressurized.

• The Main Drain Valve (F), and Low

Body Drain Valve (L) are closed.

• The Three-Way Alarm Control Valve

(E) is in the open position.

• The Pressure Gauge Valves (B) and

• The Pressure Switch Valve (J) is

open.

• The Air Supply Control Valve (K) is

open.

• System Air Pressure Gauge (G)

reads downstream air pressure.

• Water Supply Pressure Gauge (H)

reads the upstream water pressure.

II. Operation

When one or more sprinklers are acti-

vated, air pressure is reduced down-

stream of the Dry Pipe Valve. When the

air pressure is sufficiently reduced, the

water pressure overcomes the differen-

tial holding the Dry Pipe Valve closed

and the Dry Pipe Valve opens to per-

mit water flow into the system piping

and to be discharged from any open

sprinklers. Also, with the Dry Pipe

Valve open, water flows through the

Alarm Port at the rear of the Dry Pipe

Valve to actuate the Waterflow Pressure

Alarm Switch (M) and, as applicable,

the Water Motor Alarm.

III. Removing System From Service
Step 1.

Close the Main Control Valve

(A), close the Air Supply Control Valve

(K), and place the Three-Way Alarm

Control Valve (E) in the closed position.

Step 2.

Drain the system with the Main

Drain Valve (F) and by opening all auxil-

iary drain valves in the system to make

sure that cross-mains and branch lines

are drained.

IV. Placing the System Back in

Service
Step 1.

Close the auxiliary drain valves

after water ceases to discharge, and

leave the Main Drain Valve (F) open.

Step 2.

Place the Three-Way Alarm

Control Valve (E) in the open position.

Step 3.

Replace the sprinklers that

have operated and the sprinklers close

to the fire.

Step 4.

Push down on the reset knob

(P) to allow the Dry Pipe Valve (D) to

re-seat.

Step 5.

Via the Air Supply Control

Valve (K), pressurize the system with

air to 0,7 bar, and then open and close

each auxiliary drain valves in the sys-

tem piping to drain any remaining water

in trapped sections. Also, partially open

the Low Body Drain Valve (L) to assure

that the riser is completely drained.

Close the Low Body Drain Valve (L) as

soon as water ceases to discharge.

Step 6.

Open the Air Supply Control

Valve (K) to restore the system to the

normal system air pressure.

Step 7.

Partially open the Main Control

Valve (A), and then slowly close the

Main Drain Valve (F).

Step 8.

Fully open the Main Control

Valve (A) and lock it open.

Step 9.

Reset the fire alarm panel and

notify the central alarm station.

V. Weekly Test

Important:

Prior to closing any valves

or activating any alarms, notify local se-

curity guards and the central alarm sta-

tion if applicable.

Step 1.

Place the Three-Way Alarm

Control Valve (E) in the test position,

verify that the alarm signal created by

the Waterflow Pressure Alarm Switch

(M) is visible at the fire panel. If appli-

cable, check the sound of the Water

Motor Alarm — it must be clear and

steady.

Step 2.

Place the Three-Way Alarm

Control Valve (E) in the open position

and verify that the normal supply and

system pressures are restored. If the

supply pressure is below the normal,

use the instructions from the water sup-

ply to obtain the usual pressure.

Step 3.

Close the Pressure Switch

Valve (J) and verify operation of the low

air pressure Alarm Switch (N).

Step 4.

Return the Pressure Switch

Valve (J) to the normally open position

after verifying that the alarm signal is

visible at the fire panel.

Summary of Contents for ACC-1







































Search results

Summary of Contents for ACC-1

Reviews:

Related manuals for ACC-1

Brands by name

Popular brands

Tyco ACC-1, Manual

Search results

Summary of Contents for ACC-1

Reviews:

Related manuals for ACC-1

Brands by name

Popular brands