background image

Chapter 3: Replacing Pre-Installed Components

33

Chapter 3: Replacing Pre-Installed

Components

3.1

Introduction

This chapter explains how to replace pre-installed compo-
nents including the motherboard, LED control board, 
SAS/SATA backplane, and power supply.

Take note of the precautions in this section when installing 
your system.

3.1.1 Work Area

Make sure you have a stable, clean working environment. 
Dust and dirt can get into components and cause malfunc-
tions. Use containers to keep small components separated. 
Putting all small components in separate containers keeps 
them from becoming lost. Adequate lighting and proper tools 
can prevent you from accidentally damaging the internal 
components.

3.1.2 Tools

The procedures that follow require only a few tools, including 
the following:

A cross head (Phillips) screwdriver

A grounding strap or an anti-static pad

Most of the electrical and mechanical connections can be dis-
connected using your fingers. It is recommended that you do 
not use needle-nosed pliers to remove connectors as these 
can damage the soft metal or plastic parts of the connectors.

Summary of Contents for Tank GT24 (B5377) Service




































































Reviews: