TYAN S2098 Manual Download Page 29

Page: 29 / 41

http://www.TYAN.com

3.6 – Power Management Setup

Options related to power management can be altered through the following:

ACPI function

Enabled

Disabled

Toggles advanced power and
configuration done by OS.

ACPI Suspend Type

S1 (POS)

Defines ACPI system suspend
mode.

Power Management

User Define

Maximum Saving
Minimum Saving

Defines the type of power saving
features the system should follow.

Video Off Method

V/H SYNC+Blank
Blank

DPMS

Defines the method used to power
off graphics.

Video Off In Suspend

Yes

Sets the video on/off in suspend
mode.

Suspend Type

Stop Grant

Power On Suspend

Defines the suspend type for Stop
Grant or power on suspend.

MODEM Use IRQ

Sets the IRQ for the used
MODEM.

Suspend Mode

Disabled

1/2/4/8/12/20/3040/60 Min

Set the time period before the
system goes into suspend mode.

HDD Power Down

Disabled

1,5,10,20,30,45,60 minutes

Defines hard drive power down
delay.

Soft-Off by PWRBTN

Instant-Off

4-seconds

Defines the action of the power
button when pressed.

PWRON After PWR-Fail

Off

Defines whether the system will
remain off if power fails or turn on
when power is restored.

Wake Up by PCI Card

Disabled

Enabled

Defines whether the system can be
powered on by a PCI Card.

Power On by Ring or

Wake Up on LAN

Disabled

Enabled

Defines whether the system will
wake up if the modem is dialed
into. Set for default.

Summary of Contents for S2098










































Search results

Summary of Contents for S2098

Reviews:

Related manuals for S2098

Brands by name

Popular brands

TYAN S2098, Manual

Search results

Summary of Contents for S2098

Reviews:

Related manuals for S2098

Brands by name

Popular brands