Twyford SF1139CP Installation And Maintenance Instructions Manual Download Page 5

4

Technical Data

    This Sola Safe Touch thermostatic mixer tap is suitable for installations on all types of 
    plumbing system, including gravity supplies, fully pumped, modulating combination boiler, 
    unvented water heater and unbalanced supplies i.e. Cold Mains & Tank Fed Hot. They are not 
    suitable for non-modulating combination boilers.

    Max Inlet Pressure (Static)               12 bar        Max Unbalanced Pressure Ratio      15:1

    Max Inlet Pressure (Dynamic)          5 bar          with flow regulator                             

    Max Inlet Temperature                      85˚C           Max Unbalanced Pressure Ratio      5:1

    Min Inlet Temperature                       10˚C           without flow regulator                        

    Pre Set Factory Temp Setting           38˚C           Min Temp Differential to

    Min Operating Pressure (Dynamic)  0.2 bar       ensure fail-safe between hot

    Temperature Stability                        ±2˚C           and cold supplies                              10˚C

Dimensions

                                                                            

75

156

Ø50

100

132

39

148

Summary of Contents for SF1139CP

















Reviews: