background image

 

 

 

 

   

DECLARATION OF CONFORMITY

 

According to EC Directive 

 

Manufacturer:     Two-Rock Amplifiers, LLC 

Address:      

619 Martin Ave. 

 

 

 

STE 5 

 

 

 

Rohnert Park, CA 94928 

 
Phone: 

 

707-584-8663    

E-mail:     

[email protected] 

 

Product Name: 

Audio Power Amplifier 

 
Brand Name: Two-Rock 

Model Numbers/Report Numbers:  

 

Burnside:    

 

 

R130829C, R130915 

Cardiff:    

 

 

R160425, SR160430 

Classic Reverb(Signature):   R130829C, R130915 

Traditional Clean: 

 

R130829C, R130915 

Bloomfield Drive:  

 

R070212, R070213 

Coral:  

 

 

 

R070212, R070213 

Crystal:    

 

 

R130829C, R130915 

 

 

Sensor:  

 

 

 

R070212, R070213 

 

 

Studio Pro(PLUS):  

 

R130829C, R130915 

 

 

TS1:   

 

 

 

R070212, R070213 

 

 

 

 

  

Has been designed and manufactured in accordance to the following technical 
regulation: 

Directive Device: 

 

Low Voltage Equipment 2014/35/EU 

Electromagnetic Compatibility 2014/130/EU 
 

Conformity with the following standards: 

 

The measurements made in accordance with the procedures according to the 

European Council Directive and EN Standards. 
 

Council Directive and EN Standards: 

 

EN 55103-1:2009+A1:2012 

 

EN 55103-2:2009 

 

EN61000-3-2:2006+A1:2009+A2:2009 

 

EN61000-3-3:2013 

 

EN60065:2002+A1:2006+A11:2008+A2:2010+A12:2011 

 

CE mark was affixed on the products:  2007-2017 

 
The product(s) which are defined herein was (were) manufactured under the 

conditions of the European Union directive and standards.  Also, this product(s) 

responsibility is under our firm's guarantee. 

 

Manufacturer Stamp & Signature 

 

Two-Rock Amplifiers 

Mac Skinner 

 

Name surname: Mac Skinner 

Title: Owner/COO 
Date:   1/1/2018 

Summary of Contents for Bloomfield Drive 100











Reviews: