background image

59

Twin Disc, Incorporated

Power Shift Transmission System Operator’s Manual #1020510

Preventative Maintenance

Hydraulic System Pressure Checks

At the time of each transmission oil change the main and lube pressure of the
transmission should be checked. 

See Figures 3, 4, 5, and 6 in Operation  for

pressure test point locations.

Prior to making pressure checks, ensure that the transmission is filled with oil
of the correct type.

Pressures should be measured with gages or instrumentation that
allows the technician to be at a safe distance from the fracturing rig
tires.  Gages must be installed while the engine is not running.  Pressure
checks are made with the engine running, the transmission in neutral,
and the fracturing rig parking brakes on.  No one must be allowed in
front of, nor behind the fracturing rig nor near the fracturing rig tires.

Check main and lube system pressures as follows:

1.

Select desired check point and install 0-300 psi (0-2000 kPa) pressure
gauge to check main and clutch apply pressures, and 0-100 psi (0-800
kPa) pressure gauge for lube system.

2.

Start the engine, and shift to 

Warm-Up

 and bring the engine up to 1500

rpm. Allow the transmission oil to heat to  80° to 100° C.

3.

Refer to pressure requirements in Description and Specifications.

Summary of Contents for TA-90-8501

























































































































































Reviews: